Clarion DXZ815MP User Manual

Setting the Beat EQ
This unit comes with 5 types of sound tone ef-
fects stored in memory. Select the one you prefer.
*The factory default setting is "USER CUSTOM".
Each time you press BEQ button [l], the tone
effect changes in the following order:
"1 BASS BOOST" ~ "2 IMPACT" ~ "3 EXCITE"
~ "USER CUSTOM" ~ "TONE BYPASS" ...
• 1 BASS BOOST : bass emphasized
• 2 IMPACT : bass and treble emphasized
• 3 EXCITE : bass and treble emphasiaed
mid de emphasised
• USER CUSTOM :
user custom
• TONE BYPASS : no sound effect
Adjusting the tone
Press A-M button [g] and select the item to ad-
just. Each time you press A-M button
[g], the item
changes in the following order:
• When the BEQ (BASS BOOST, IMPACT,
EXCITE)
is set
"NON-FAD VOL:' ~ "BASS BOOST"( IMPACT,
EXCITE) ~ "BALANCE" ~ "FADER" ~
Function mode ...
• When the BEQ (USER CUSTOM) is set
"NON-FAD VOL" ~ "BASS" ~ "MID"
"TREBLE" ~ "BALANCE" ~ "FADER" ~
Function mode...
• When the, BEQ is off
"NON-FAD VOL" ~ "BALANCE" ~
"FADER" ~ Function mode...
* Pressing the SEQ button [l] for 1 second or longer
while in "USER-CUSTOM" sets flat, and displays
a "BEQ FLAT" message.
Note:
• When the separately-sold digital sound processor
(DPH910) is used, the bass
and treble tone adjust-
ments cannot be selected.
To adjust the tone, refer
to the section "DSP Operations".
Adjusting the non fader output
volume
You can adjust the volume output from the unit's
non fader output terminal.
1. Press A-M button [g] and select "NON-FAD
VOL".
2. Turning the Rotary knob [lID clockwise in-
creases the output volume; turning it coun-
terclockwise decreases the output volume.
*The factory default setting is "0". (Setting range:
-6 to 6)
Basic Operations
3. When the adjustment is complete, press A-M
button
[g] several times until the function mode
is reached.
Adjusting the bass
The bass gain, bass F (center frequency) and
bass Q can be adjusted as follows.
1. Press the A-M button [g] and select "BASS
~GAIN~".
2. Press the SEARCH button ~ and select from
"BASS ~GAIN~" ~ "BASS ~F 50~" ~
"BASS ~Q 1~" ~ "BASS ~GAIN~".
3. Turn the Rotary knob [lID clockwise or coun-
terclockwise as needed and adjust the gain,
the F (center frequency) and the Q.
BASS GAIN: -6 to 8 (The factory default
setting is "0")
BASS F : 50Hz/80Hz/120Hz (The fac-
tory default setting is "50")
BASS Q : 1/1.25/1.5/2 (The factory de-
fault setting is
"1")
4. When the adjustment is complete, press A-M
button
[g] several times until the function mode
is reached.
Adjusting the MID
The MID gain, MID F (center frequency) and MID
Q can be adjusted as follows.
1. Press the A-M button l!ID and select MID GAIN.
2. Press the SEARCH button
~ and select from
"MID ~GAIN~" ~ "MID ~F 1 k~" ~ "MID ~Q
2~" ~ "MID ~GAIN~".
3. Turn the Rotary knob ITID clockwise or coun-
terclockwise as needed and adjust the gain,
the F (center frequency) and the Q.
MID
GAIN: -6 to 6 (The factory default set-
ting is "0")
MID F : 700Hz/1 KHz/2KHz (The factory
default setting is
"1 k")
MID Q : 1.5/2 (The factory default setting
is "2")
4. When the adfustment is complete, press A-M
[g] button several times until the function mode
is reached.
Adjusting the TREBLE
The treble gain and treble F (center frequency)
can be adjusted as follows.
1. Press the A-M button l!ID and select "TREB
GAIN".
nX7R1~MP 11

Clarion DXZ815MP Specifications

General

Brand	Clarion
Model	DXZ815MP
Category	Car Receiver
Language	English