Basic
Operations
Adjusting
the Sub-woofer
and
Center Speaker
• "SW VOLUME" (sub-woofer) can be adjusted
only when "SUB-WOOFER" is set to "ON".
• "CTR VOLUME" (center speaker) can be
adjusted only when the Dolby Pro Logic
II
mode is set to either "MUSIC"
or
"MATRIX",
"SP-SETTING" is set to "CTR+SW" and
"CENTER-SP" is set to "ON".
• The factory default setting for
SW
VOLUME is
"0" and for
eTR
VOLUME is "0".
1. Press the [SOUND] button.
2. Touch A-MODE.
4.
To
change the details of the
ADF
setting,
press the [A] button.
5.
Touch -t
I:i
~on
the adjustment item display
to select the desired item.
Each touch of
-tl:i~
switches the
adjustment item display as follows:
.Adjustment
item
(when
USER
is
selected
in
step
3)
BASS
-.
TREBLE
-.
COMP
-.
BASS
...
.Adjustment
item
(when
1
to
3
is
selected
in
step
3)
LEVEL
-.
COMP
-.
LEVEL
...
6. Touch
-t
I:i
~
on the right of the display to
adjust the item.
* "BASS" and "TREBLE" can be adjusted
within the range 1 to 13.
* "LEVEL" can be adjusted within the range
-3 to +3.
* Select either "ON"
or
"OFF" for "COMP".
7.
Press the [SOUND] button to return to the
original mode.
)OFFF
~
POSITION
P.
EQ
Dolby
PLll
RTN
------SOUNDMENU------
2 •
ZONE
ADF
A •
MODE
T'fOFF:t
·~OFF~·
3.
Touch
-t
I:i
~
on the right of the display to
select the ADF mode.
Setting the
ADF
• ADF is the abbreviation
of
Anti Distortion
Filter.
The adopted
"Liveliness
Enhancement
Filter"
and
"Sound
Tone
Compensation"
functions
allow well-modulated realistic playback without
affecting the characteristics of the original sound
tone.
This unit are provided with 4 types of sound
tone effects stored in memory. Select the one
you prefer.
ADF-1 : Suitable for genuine speakers
ADF-2:
Suitable for separate speakers
ADF-3:
Suitable for co-axial speakers
USER : This setting can be adjusted by the
user to his or
her
individual preference.
OFF : No sound effect
• The factory default setting for "OFF".
Notes:
•
As
the volume changes when
ADF
is switched,
switch
ADF
with the volume
and
"SW
VOLUME"
(sub-woofer)
and
"CTR
VOLUME"
(center
speaker) turned down
as far as possible.
• On
some
speaker
systems, sufficient effect
sometimes
cannot
be
obtained.
If
this happens,
adjust the
ADF
parameter
or
the volume.
• When
ADF
is
set
to "USER", "1", "2"
or
"3",
the
VSE function
and
BASSfrREB
function
under
EO-SELECT
are disabled.
1.
Press the [SOUND] button.
2.
Touch
ADF.
•
To
stop
scrolling
Touch
I:i
~
on the title display.
3.
Touch -t
I:i
~
on the adjustment item display
~
to select "SW VOLUME" or "CTR VOLUME".
When ADF is set to "OFF", the ADF setting
is not reflected on the music source. This
ends the ADF setting. Press the [SOUND]
button to return to the original mode.
* Select one of USER,
1,
2,
3,
or OFF.
DXZ945MP 15
To Next Page
Loading...
