P.EQ
basic
menu
AC-ProcessorIII Operations
9.
Touch
-t1)1'
on the right
of
the display and
adjust the item as desired.
*
"BAND"
can be adjusted within the range
1 to
3.
* "FREQ" can be adjusted within the range
20Hz to 20kHz.
* Select one of
1,
3,
5,
7,
or
20 as "Q".
* "GAIN" can be adjusted within the range
-12dB to +12dB.
10. Repeat steps 7 to 9 to adjust the desired
item.
11.
When you have finished adjusting each item,
touch RTN.
The display returns to the original screen,
and
"»"
is displayed
at
the BASIC
or
USER
display.
Operation so far completes PEQ
adjustment.
To
continue to store the
adjustment values to the
P.EQ
user menu
perform the following. '
12. Touch and hold RTN for 1 second
or
longer.
The
PEQ
menu list is displayed.
13. Touch and hold the user memory you want
to store the adjustment values to for 2
seconds or longer.
You
will hear a long beep, and the values
you adjusted up to step 10 are stored to the
P.EQ
menu.
If you hear a short beep, the adjustment
values up to step 10 are discarded. Adjust
these values again as required.
14. Touch RTN.
15. Press the [SOUND] button to return to the
original mode.
*
To
select a stored user memory, touch B/U
to display "USER" and touch
"t
I)
l'
on the
user memory No.
•
P.EQ
adjustment
The settings that can be adjusted in the
P.EQ
menu are as follows. The center frequency, gain
and Q curve can be stored to channel/band
combinations.
For example, center frequency "250Hz",
gain"
-8dB"
and Q curve "3" can be stored to band 1
on the front.
FRONT/REAR
(channel
selection)
Selects the channel (front
or
rear) to adjust.
BAND
(band
selection)
Selects the frequency band
(1
to 3) to adjust.
Set the center frequency (FREQUENCY), gain
(GAIN) and Q curve (Q) for each frequency
band.
~
RTN
P1.EQEDIT
BAND
»
6. Press the [SOUND] button to return to the
original mode.
Adjusting/storing
P.EQ
(user
memory)
With user memory, you can compensate the
frequency characteristics to suit your car based
upon the
REQ
basic menu. Up to 6 adjustment
setups can be stored to user memory. For
details, see "P.EQ
adjustment".
1.
Press the [SOUND] button.
2. Touch P EQ.
3.
Touch
"t
I)
i"
on the ON/OFF display.
The
P.EQ
effect is toggled
ON/OFF
4. Touch B/U to select "BASIC"
or
"USER".
5.
Touch
"t
I)
i"
on the right
of
the display to
select the menu that is used as the menu for
adjustment.
6.
Press the [A] button.
7.
Touch
"t
I)
l'
on the left
of
the display to
select "FRONT"
or
"REAR".
8.
Touch
"t
I)
i"
on the center
of
the display to
select each adjustment item.
Each touch
of
"t
I)
i"
switches the
adjustment item as follows:
Adjustment
items
BAND'"
FREQ
...
Q
...
GAIN'"
BAND
...
No.
Display
name
Speaker
Mounting
position
1 SEDAN-1
Front: Front door
Rear:
Rear parcel
2 SEDAN-2
Front: Front door
Rear:
Rear door
3
WAGON-1
Front: Front door
Rear:
Luggage (side)
4 WAGON-2
Front: Front door
Rear:
Rear door
5
MINI VAN-1 Front: Front door
Rear:
Luggage (side)
6
MINI VAN-2 Front: Front door
Rear:
Rear door
DXZ945MP
21
To Next Page
Loading...
