Craftsman 247.881720 - User Manual

Questions and Answers

A
Andrew VelazquezAug 8, 2025
How to fix a Craftsman 247.881720 Snow Blower when the engine fails to start?
- P
  Paige WhiteAug 8, 2025
  If your Craftsman Snow Blower engine won't start, try these steps: 1. Ensure the choke control is in the CHOKE position. 2. Connect the spark plug wire securely. 3. Inspect the spark plug; clean, adjust the gap, or replace if necessary. 4. Fill the fuel tank with fresh gasoline. 5. Prime the engine as per the instructions in the Operation Section. 6. Insert the key fully into the switch. 7. If equipped with an electric start, connect the extension cord to a grounded AC outlet.
J
John LiuAug 12, 2025
Why is my Craftsman 247.881720 engine running erratically?
- S
  Sean RodriguezAug 12, 2025
  To resolve erratic engine performance (hunting or surging) in your Craftsman Snow Blower: 1. Ensure the choke control is in the RUN position. 2. Replace stale fuel with clean, fresh gasoline. 3. Drain the fuel tank to remove any water or dirt, then refill with fresh fuel. 4. If the engine is over-governed, contact your Sears Parts & Repair Center.
J
Jack VelezAug 16, 2025
What to do if my Craftsman 247.881720 Snow Blower won't move?
- D
  Danielle BrooksAug 16, 2025
  If your Craftsman Snow Blower won't propel itself: 1. Adjust the drive control cable. Refer to the Service and Maintenance section. 2. For drive belt issues, refer to the Service and Maintenance section. 3. If the friction wheel is worn, have it replaced at a Sears Parts & Repair Center.
P
Paul ParkerAug 20, 2025
What to do if my Craftsman 247.881720 Snow Blower fails to discharge snow?
- M
  Mariah GutierrezAug 20, 2025
  If your Craftsman Snow Blower isn't discharging snow, here's what to check: 1. Immediately stop the engine and disconnect the spark plug wire before cleaning any clogs in the chute assembly and inside the auger housing using a clean-out tool or stick. 2. If there's a foreign object in the auger, stop the engine immediately, disconnect the spark plug wire, and remove the object with a clean-out tool or stick. 3. For auger cable adjustments, refer to the Assembly section. 4. For auger belt issues, refer to the Service and Maintenance section. 5. Replace any sheared shear pins with new ones.
A
Amy PerezAug 25, 2025
Why is my Craftsman 247.881720 losing power?
- A
  Angel BarnettAug 26, 2025
  If your Craftsman Snow Blower experiences loss of power: 1. Check and tighten the spark plug wire. 2. Ensure the gas cap vent hole is clear of ice and snow.
K
Kimberly KnightAug 29, 2025
How to stop excessive vibration in my Craftsman Snow Blower?
- D
  Danielle EstradaAug 29, 2025
  If you notice excessive vibration in your Craftsman Snow Blower: 1. Immediately stop the engine and disconnect the spark plug wire. 2. Tighten all bolts and nuts. 3. If the vibration persists, have the unit serviced by a Sears Parts & Repair Center.
R
robertsoncheyenneSep 2, 2025
How to fix a Craftsman Snow Blower chute that won't rotate?
- J
  John RobinsonSep 3, 2025
  If the chute on your Craftsman Snow Blower doesn't rotate easily: 1. Disassemble and reassemble the chute control as directed in the Assembly section.