FAILURETOHEEDALLSAFETYAND OPERATINGINSTRUCTIONS
ANDWARNINGSREGARDINGUSEOFTHISPRODUCTCANRESULT
IN SERIOUS80DILY INJURY.
GENERALSAFETYINSTRUCTIONSFORPOWERTOOLS
1. KNOWYOURPOWERTOOL
Readthe owner'smanualcarefully.Learnits applicationand
limitationsaswell asthe specific potentialhazardspeculiarto this
toot.
2. GROUNDALLTOOLS(UNLESSDOUBLEINSULATED)
Iftool isequippedwith anapproved3-conductor cordand a3-
prong groundingtype plug, it should bepluggedintoa threehole
electricalreceptacle,Ifadapteris usedto accommodatea two-
prong receptacle,theadapterwire must be attachedto known
ground,(usuaflythe screw securing receptaclecover plate).Never
removethird prong.Neverconnectgreen ground wireto a
terminal.
3. KEEPGUARDSIN PLACE
Inworking order,andin properadjustmentand alignment,
4. REMOVEADJUSTINGKEYSANDWRENCHES
Forma habit of checkingto seethat keys andadjusting wrenches
areremovedfrom too! beforeturning it on.
5. KEEPWORKAREACLEAN
Clutteredareasandbenchesinvite accidents,Floormustnot be
slipperydue towax or sawdust.
6. AVOIDDANGEROUSENVIRONMENT
Don't usepowertools in dampor wet locationsor exposetllem to
rain.Keepwork areawel!lighted: Provideadequatesurrounding
work space.
7. KEEPCHILDRENAWAY
All visitors shouldbe kepta safedistancefrom work area.
8. MAKEWORKSHOPKID-PROOF
Usepadlocks,masterswitches, or removestarter keys.
9, DON'TFORCETOOLS
It wilt do thejob betterand saferat the rate for which it was
designed,
10. USERIGHTTOOL
Don'tforcetoot or attachmentto do a job it was not designedfor.
11. WEARRIGHTAPPAREL
Do notwearlooseclothing,gloves, necktiesor jewelry (rings,
wrist watches)to getcaugt]tin moving parts, Nonslipfootwear is
recommended,Wearprotectivehair coveringto contain long flair.
Rolllong sleevesabovethe elbow.
12. USESAFETYGOGGLES(HeadProtection)
WearSafetygoggles(mustcomplywith ANSI'Z87,1)at alltimes.
Also, usefaceor dust mask,if cutting operationisdusty,andear
protectors (plugsor muffs) during extendedperiodsof operation.
13. SECUREWORK
Useclamps or a viseto hold work whenpractical, It's saferthan
using your hands,andit frees both handsto operatetool,
14. DON'TOVERREACH
Keepproper footing and balanceatatftimes.
i5. MAINTAINTOOLSWITHCARE
Keeptools sharpand cleanfor bestand safestperformance.
Follow instructionsfor lubricatingand changingaccessories.
16. DISCONNECTTOOLS
Beforeservicing,whenchangingaccessoriessuch as blades,bits,
cutters,etc.
17. AVOIDACCIDENTALSTARTING
Make sureswitch is in "OFF"position beforepluggingin.
18. USERECOMMEND_EDACCESSORIES
Consulttheowner's manualfor recommendedaccessoriesand
follow the instructions,The use of improper accessoriesmay
causehazards.
19. NEVERSTANDONTOOL
Serious injurycould occur if thetool is tippedor if the cutting tool
is accidenta!lycontacted. Do not store materials aboveor nearthe
tool makingit necessaryto stand onthe tool to reachthem.
20. CHECKDAMAGEDPARTS
Beforefurther use of the tool, any guardor other partthat is
damagedshould becarefullycheckedto ensurethat it will operate
properlyand perform its intendedfunction. Checkforalignmentof
moving parts,binding of moving parts,breakageof parts,
mounting,andany other conditions that may affect its operation.A
guard or anyother partthat is damagedshould be properly
repairedor replaced.
21. DIRECTIONOFFEED
Feedwork into a bladeor cutter againstthedirection of rotation of
the bladeor cutteronly.
22. NEVERLEAVETOOLRUNNINGUNATTENDED
Turn poweroff. Don't leavetool until it comes to a completestop,
To Next Page
Loading...
