FAILURE TO HEED ALL SAFETY AND OPERATING INSTRUCTIONS AND WARNINGS
REGARDING USE OF THIS PRODUCT CAN RESULT IN SERIOUS BODILY INJURY.
GENERALSAFETYINSTRUCTIONSFORPOWERTOOLS
1) KNOWYOURPOWERTOOL
Readthe owner's manual carefully. Learn its applica-
tions andlimitations as well as the specific potential
hazardsparticular to this tool.
2) GROUNDALLTOOLS(UNLESSDOUBLEINSU-
LATED)
If tool is equippedwith an approved3-conductor cord
and a3-prong grounding type plug, it shouldbe
pluggedinto a three hole electricalreceptacle, if
adapteris used to accommodate atwo-prong recep-
tacle,the adapterwire must be attachedto known
ground, (usually the screw securingreceptaclecover
plate). Neverremovethird prong. Neverconnect green
groundwire to a terminal.
3) KEEPGUARDSIN PLACE
in working order, andin proper adjustment andalign-
ment.
4) REMOVEADJUSTINGKEYSANDWRENCHES
Forma habit of checking to seethat keys and adjusting
wrenchesare removed from tool beforeturning it on,
5) KEEPWORKAREACLEAN
Clutteredareasand benchesinvite accidents. Floor
must not beslipperydueto wax or sawdust.
8) AVOIDDANGEROUSENVIRONMENT
Do notusepowertoolsindampor wetlocationsor
exposethem to rain. Keepwork areawell lighted.
Provideadequatesurrounding work space.
7) KEEPCHILDRENAWAY
All visitors should be kept at a safedistance from work
area.
8) MAKEWORKSHOPCHILD-PROOF
--with padlocks, master switches, or by removing
starter keys.
9) DONOTFORCETOOL
it willdo the job betterand safer at the rate for whichit
was designed.
10) USEAPPROPRIATETOOL
Do not force tool or attachmentto do ajob for which it
was not designed.
11) WEARAPPROPRIATEAPPAREL
Do not wear looseclothing, gloves, necktiesor jewelry
(rings, wristwatches) to get caught in moving parts.
Non-slip footwear is recommended.Wear protective
hair coveringto contain long hair. Roll long sleeves
abovethe elbow,
12) USESAFETYGOGGLES(HeadProtection)
WearSafety Goggles(must comply withANSIZ87.1) at
alltimes.Also,useface or dustmask if cuttingoperat-
ingisdusty,andearprotectors (plugsor muffs)during
extendedperiods of operation. ,
13) SECUREWORK
Useclamps or a vise to hold work when practical, It's
saferthan using your hand andfrees both handsto
operatetool.
14) DONOTOVERREACH
Keepproper footing andbalanceat all times.
15) MAINTAINTOOLSWITH CARE
Keeptools sharpandcleanfor best andsafestperfor-
mance.Followinstructions for lubricating andchanging
accessories.
16) DISCONNECTTOOLSBEFORESERVICING
-when changingaccessoriessuchas blades,bits,
cutters,etc,
17) AVOIDACCIDENTALSTARTING
Makesureswitchisin OFFpositionbeforepluggingin.
18) USERECOMMENDEDACCESSORIES
Consultthe owner'smanualfor recommendedacces-
sories.Followthe instructionsthataccompanythe
accessories.Theuse of improperaccessoriesmay
causehazards.
19) NEVERSTANDONTOOL
Seriousinjurycouldoccurifthe tootistipped or the
cuttingtool is accidentallycontacted.Donotstore
materialsaboveor nearthetool that wouldmake it
necessaryto standonthetoolto reachthem.
20) CHECKDAMAGEDPARTS
Beforefurther useofthetool,a guardor otherpartthat
isdamagedshouldbecarefullycheckedto ensurethat
it will operateproperly andperform itsintendedfunc-
tion.Checkfor alignmentof moving parts, bindingof
movingparts,breakageofparts, mounting,andany
otherconditionsthatmay affectitsoperation.A guard
or otherpart that is damagedshouldbeproperly
repairedor replaced,
21) DIRECTIONOF FEED
Feedworkintoa bladeor cutteronlyagainstthedirec-
tionof rotation of thebladeor cutter,
22) NEVERLEAVETOOLRUNNINGUNATTENDED
Turnpower off. Do not leavetool untilit comesto a
completestop.
1
READANDUNDERSTANDTHISCOMPLETEINSTRUCTIONBOOKBEFOREUSINGTHIS PRODUCT.
To Next Page
Loading...
Need help?
General
