Da-Lite PROFESSIONAL ELECTROL

Questions and Answers

J
jennifermoranAug 17, 2025
What to do if my Da-Lite PROFESSIONAL ELECTROL Projection Screen will not go down?
- L
  Linda TuckerAug 17, 2025
  If your Da-Lite Projection Screen isn't operating or going down and the motor isn't humming, it could be due to several reasons: * A blown facility fuse: Replace the facility fuse. * A tripped facility circuit breaker: Reset the circuit breaker. * No power to the operating switch or junction box: Check the power supply. * Thermal overload tripped at the junction box: Tighten all loose wire connections. Additionally, a broken wire in the 'down' position requires rechecking the wiring. Temporary binding can be resolved by turning the roller by hand with the power off. If the motor, limit switch, or capacitor is defective, consult the installation instructions. A burned-out capacitor necessitates replacing the motor assembly.
B
brenda32Aug 19, 2025
What to do if my Da-Lite PROFESSIONAL ELECTROL will not move upward?
- T
  taylorjocelynAug 19, 2025
  If your Da-Lite Projection Screen won't move upward, and the motor isn't humming, it might be due to: * A blown facility fuse: Replace the facility fuse. * A tripped facility circuit breaker: Reset the circuit breaker. * No power to the operating switch or junction box: Check the power supply. * Power at the junction box and thermal overload tripped: Tighten all loose wire connections. If the motor hums but the screen still doesn't move, it could be a broken wire in the 'up' position (check the wiring), a defective motor, limit switch, or capacitor (check for continuity). Temporary binding can be resolved by turning the roller by hand with the power off. A burned-out capacitor requires replacing the motor assembly.
B
Blake WilliamsAug 22, 2025
Why does the fabric on my Da-Lite PROFESSIONAL ELECTROL Projection Screen hang crooked?
- J
  Jennifer NobleAug 22, 2025
  If your Da-Lite Projection Screen fabric hangs crooked, it could be due to a few reasons. First, ensure the screen is installed properly by checking if it's level and plumb. If the fabric has backed up inside the case, adjust the 'down' limit switch slowly until the roller is exposed and the wrinkle comes out, then readjust for proper drop. If the fabric is damaged, consider replacing it.
R
robert45Aug 25, 2025
What to do if the roller is displaced from the mounting bracket of my Da-Lite PROFESSIONAL ELECTROL?
- J
  Jamie MurphyAug 26, 2025
  If your Da-Lite Projection Screen roller is displaced from the mounting bracket because the pin end slipped out of the nylon bearing, remove the pin end mounting, realign the motor in the tube, and then reattach the pin end.
J
Jonathan BennettAug 28, 2025
How to fix a noisy Da-Lite Projection Screen?
- T
  trevor31Aug 28, 2025
  If your Da-Lite Projection Screen is making excessive noise, it could be due to a few reasons. A squeaking sound might indicate the rubber end plug is rubbing on the motor; try centering the roller between the mounting brackets by pushing the roller away from the motor end. A grinding sound could mean there's a foreign object rubbing on the roller or fabric, so remove it. Gear noise may require replacing the motor assembly.
J
Jennifer KnightAug 30, 2025
What causes coasting in a Da-Lite PROFESSIONAL ELECTROL Projection Screen?
- S
  Stacy CampbellAug 30, 2025
  If your Da-Lite Projection Screen is coasting, it is caused by a defective brake. To resolve this, replace the motor assembly.
W
Whitney GordonSep 8, 2025
How to fix noise coming from Da-Lite PROFESSIONAL ELECTROL?
- K
  Kimberly MezaSep 8, 2025
  If your Da-Lite Projection Screen is making noise, here are a few possible causes and solutions: * If it's a squeaking sound, the rubber end plug might be rubbing on the motor. Center the roller between the mounting brackets by pushing the roller away from the motor end. * If it's a grinding noise, there might be a foreign object rubbing on the roller or fabric. Remove the foreign object. * If it's gear noise, the motor assembly may need to be replaced.
S
Sheri WilliamsSep 10, 2025
What to do if Da-Lite PROFESSIONAL ELECTROL is coasting?
- J
  Jonathan DavisSep 10, 2025
  If your Da-Lite Projection Screen is coasting, the brake may be defective. Replace the motor assembly.
V
Victor JimenezSep 13, 2025
What to do if roller is displaced from mounting bracket of Da-Lite PROFESSIONAL ELECTROL?
- R
  ryanmcdonaldSep 13, 2025
  If the roller is displaced from the mounting bracket on your Da-Lite Projection Screen because the pin end slipped out of the nylon bearing, remove the pin end mounting, realign the motor in the tube, and reattach the pin end.
E
Eric PaceDec 3, 2025
What to do if Da-Lite PROFESSIONAL ELECTROL will not go down?

Summary

Important Safety Instructions

Screen Unpacking and Preparation

Steps for carefully unpacking the screen, checking measurements, and preparing for installation.

Integrated Ironing Board

Details the function of the ironing board on larger screens and advises when to seek professional adjustment.

Installation Methods

Screen Size and Mounting Diagrams

Illustrations showing dimensions for screens up to 18' and 20'+, with various mounting options.

Mounting Hardware and Techniques

Guidance on using wall/ceiling hangers, flush mounts, and recessed installation methods for the screen.

Installation Process

Hanger Placement and Handling

Instructions for correct hanger placement, removing shipping braces, and managing protective wrapping.

Electrical Connection and Testing

Steps for performing electrical hookup and initial testing of the installed screen system.

Wiring and Electrical Setup

120 V System Wiring Diagram

Detailed diagram and instructions for connecting a 120V system, including switch configurations.

240 V System Wiring Guide

Information and diagrams for wiring 240V systems with standard wall switches for screen operation.

Screen Adjustment Guide

Adjusting Screen Travel Limits

Procedures for modifying the screen's upper and lower travel limits using adjustment knobs for precise positioning.

Troubleshooting Common Issues

Screen Fails to Operate or Move Down

Solutions for screens not operating or moving down, covering electrical faults, power loss, and component issues.

Motor Hums But Screen Stays Still

Troubleshooting tips for when the motor hums but the screen movement is inhibited, such as binding or component failure.

Screen Fails to Move Upward

Guidance on diagnosing and resolving issues that prevent the screen from moving upward, including electrical and mechanical checks.

Advanced Troubleshooting

Limit Switch and Noise Resolution

Fixes for 'down' limit switch errors and common noise problems like squeaking, grinding, or gear sounds.

Roller and Fabric Alignment

Solutions for roller displacement, defective brakes, and fabric hanging issues, including alignment and replacement advice.

Product Warranty Information

Da-Lite PROFESSIONAL ELECTROL Specifications

General

Screen Type	Electric
Series	Professional Electrol
Aspect Ratio	16:9
Control Options	remote control
Mounting	Wall or Ceiling
Operation	Motorized
Housing	Black aluminum