9/11
Breadcrumb Field code Setting name Range, step
Default value
Date Value
Field settings table
Installer setting at variance with
default value
9.I [7-05] R/W
0: Very high
1: High
2: Medium
3: Low
4: Ver
low
9.I [7-06] R/W
0: Disabled
1: Enabled
9.I [7-07] R/W
0: Disabled
1: Enabled
9.I [8-00] R/O
0~20 min, step 1 min
1 min
9.I [8-01] R/W 5~95 min, step: 5 min
30 min
9.I [8-02] R/W 0~10 hour, step: 0,5 hour
3 hour
9.I [8-03] R/W 20~95 min, step: 5 min
50 min
9.I [8-04] R/W 0~95 min, step: 5 min
95 min
9.I [8-05] R/W
0: No
1: Yes
9.I [8-06] R/W 0~10°C, step: 1°C
5°C
9.I [8-07] R/W [9-03]~[9-02], step: 1°C
18°C
9.I [8-08] R/W [9-03]~[9-02], step: 1°C
20°C
9.I [8-09] R/W [9-01]~[9-00], step: 1°C
35°C
9.I [8-0A] R/W [9-01]~[9-00], step: 1°C
33°C
9.I [8-0B]
13
9.I [8-0C]
10
9.I [8-0D]
16
9.I [9-00] R/W [2-0C]=2:
37~60, step: 1°C
60°C
[2-0C]≠2:
37~55, step: 1°C
55°C
9.I [9-01] R/W 15~37°C, step: 1°C
25°C
9.I [9-02] R/W 18~22°C, step: 1°C
22°C
9.I [9-03] R/W 5~18°C, step: 1°C
7°C
9.I [9-04] R/W 1~4°C, step: 1°C
4°C
9.I [9-05] R/W 15~37°C, step: 1°C
25°C
9.I [9-06] R/W [2-0D]=2:
37~60, step: 1°C
60°C
[2-0D]≠2:
37~55, step: 1°C
55°C
9.I [9-07] R/W 5~18°C, step: 1°C
7°C
9.I [9-08] R/W 18~22°C, step: 1°C
22°C
9.I [9-09] R/W 1~18°C, step: 1°C
18°C
9.I [9-0A] R/W [3-07]～[3-06]°C, step: 0,5°C
23°C
9.I [9-0B] R/W [3-09]～[3-08]°C, step: 0,5°C
23°C
9.I [9-0C] R/W 1~6°C, step: 0,5°C
1 °C
9.I [9-0D] R/W 0~8, step:1
0 : No limitation
1~4 : 80~50%
5~8 : 80~50% during sampling
6
9.I [9-0E]
6
9.I [C-00] R/W 0: Solar priority
1: Heat
9.I [C-01]
0
9.I [C-02] R/W
0: No
1: Bivalent
9.I [C-03] R/W -25~25°C, step: 1°C
0°C
9.I [C-04] R/W 2~10°C, step 1°C
3°C
9.I [C-05] R/W 0: -
1: 1 contact
2: 2 contacts
9.I [C-06] R/W 0: -
1: 1 contact
2: 2 contacts
9.I [C-07] R/W
0: LWT control
1: Ext RT control
2: RT control
9.I [C-08] R/W
0: No
1: Outdoor sensor
2: Room sensor
9.I [C-09] R/W
0: Normally open
1: Normall
closed
9.I [C-0A]
0
9.I [C-0B]
0
9.I [C-0C]
0
9.I [C-0D]
0
9.I [C-0E]
0
Boiler efficiency
HP Forced OFF
BBR16 activation
Minimum running time for domestic hot water operation.
Maximum running time for domestic hot water operation.
Anti-recycling time.
Booster heater delay timer.
Additional running time for the maximum running time.
Allow modulation of the LWT to control the room temp?
Leaving water temperature maximum modulation.
What is the desired comfort main LWT in cooling?
What is the desired eco main LWT in cooling?
What is the desired comfort main LWT in heating?
What is the desired eco main LWT in heating?
--
--
--
What is the maximum desired LWT for main zone in heating?
What is the mimimum desired LWT for main zone in heating?
What is the maximum desired LWT for main zone in cooling?
What is the mimimum desired LWT for main zone in cooling?
Leaving water temperature overshoot temperature.
What is the mimimum desired LWT for add. zone in heating?
What is the maximum desired LWT for add. zone in heating?
What is the mimimum desired LWT for add. zone in cooling?
What is the maximum desired LWT for add. zone in cooling?
What is the allowed undershoot in cooling?
Room temperature hysteresis.
Pump speed limitation
--
Domestic heating water priority.
--
What is the room buffering temperature in heating?
What is the room buffering temperature in Cooling?
Is an external backup heat source connected?
Bivalent activation temperature.
Bivalent hysteresis temperature.
What is the thermo request contact type for the main zone?
What is the thermo request contact type for the add. zone?
What is the unit control method in space operation?
Which type of external sensor is installed?
What is the required alarm output contact type?
--
--
--
--
--
(*1) *V3/W1
(*2) *3V3/3W1
(*3) EDLA*
(*4) EBLA*
(#) Setting is not applicable for this unit. 4P627273-1 - 2020.09
To Next Page
Loading...
