iRHsR7NVpxFqwbqvez8KS0CDJ5aoKKLrpBlpg5ETkYEew/uTZ14lQQRBrzPw
GBfxvTXKCWiI2j5KFa/WKLSnmWJX0/98qpxW/lMXoXsA9iK4pnMKwAAAI
B4Jrt6jmoLybpzgOPOI0DsJ7jQwWacinD0jliz8k+qzCpanhd2wH+DEdj/xO2sFR
fnYlME3hmXoB+7NByVUtheVjuQ2CWhcGFIKm9tbuPC6DtXh1xxT0NJ7rspv
Lgb0s6y/0tk+94ZP5RCoAtLZ7wirShy3/KJ4RE0y2SFZjIVjQ=="
console(config-pubkey-key)#exit
console(config-pubkey-chain)#exit
console(config)#exit
console#show crypto key pubkey-chain ssh username asd
Username : asd
ssh-dss
AAAAB3NzaC1kc3MAAACBAJRwUAD3AuRACp1MObBeh1AgyZb18wf9Bt
dip+t+1CbAqiqNEh4lBiew184DSKk0T6SnSSXuCN+bJnQPxJeiQt+OFnmjiYhn
HcvI04Q5KnQhloZcEFgSsmQ7zJnReWtLvUQI0QvBIStanzedmQVGHvDrQ5X
2R729ToSH0ibBrnYtAAAAFQDNord7S9EJvUkKKxVBpWE6/skCmQAAAIB
MjMO+BPP5KXzNWfZhqAhxBSoBvif/z6pzi9xWLlYy99A03zmRYCpcGIoLW
iRHsR7NVpxFqwbqvez8KS0CDJ5aoKKLrpBlpg5ETkYEew/uTZ14lQQRBrzPw
GBfxvTXKCWiI2j5KFa/WKLSnmWJX0/98qpxW/lMXoXsA9iK4pnMKwAAAI
B4Jrt6jmoLybpzgOPOI0DsJ7jQwWacinD0jliz8k+qzCpanhd2wH+DEdj/xO2sFR
fnYlME3hmXoB+7NByVUtheVjuQ2CWhcGFIKm9tbuPC6DtXh1xxT0NJ7rspv
Lgb0s6y/0tk+94ZP5RCoAtLZ7wirShy3/KJ4RE0y2SFZjIVjQ==
Fingerprint : d9:d1:21:ad:26:41:ba:43:b1:dc:5c:6c:b9:57:07:6c
SSH RSA or DSA keys can be generated by using the ssh-keygen command on a
Unix system or with other publicly available utilities.
Broadcom NIC link always stays up
within the m8024-k status even after
disabling server port through device
manager or turning off server altogether.
Low- This is works as designed and is necessary for new features for 12G.
The Broadcom NIC 57810S never reports to the internal switch that the link is
down because it needs the link to be up so that internal communications can
continue with iDRAC and for other various components even after disabling the
link on the server side.
Release 4.2.0.4
Layer 2 – 4.2.0.4
802.1x Authentication
Description User Impact
Windows Vista® Authentication - The
Windows Vista® client could fail to
authenticate properly when the option to
cache user credentials is selected.
Low
Workaround:
1. In Control Panel Network Connections, right-click on the desired
Local Area Connection and select Properties.
2. In the Properties window, select the Authentication tab.
3. Deselect the checkbox for Cache user information for subsequent
connections to this network.
4. Click OK.
The maximum number of 802.1x clients
per port is 4.
Low – most deployments will have at most 2 802.1x clients per physical port.
Note: If running Release 5.1.0.1 or later version of firmware, the maximum
number is 24.
The maximum number of configurable
traffic classes is 7.
Low as most deployments use a single traffic class. Some limited deployments
may use up to 3 traffic classes.
To Next Page
Loading...
