33
For 10Ó Contractor’s Saw
®
No. 34-965 Belt Guard. Encloses entire
V-belt and motor pulley, preventing small
pieces of stock from striking and damaging
the belt or pulley during operation. 4 Ibs.
No. 78-963 Biesemeyer T-Square
®
Anti-
Kickback Snap-In Spreader. Complete with
spring-loaded anti-kickback fingers. 6 lbs.
For 10Ó Contractor’s Saw
®
,
10Ó Contractor’s Saw
®
II &
10Ó Tilting Arbor Saw (cont’d)
No. 78-934 Right Extension Table. For use
with No. 78-931 and 79-012 Biesemeyer
40Ó T-Square
®
Home Shop Fence Systems.
27Ó x 34Ó. White.
No. 78-938 Right Extension Table. For use
with No. 78-935 and 79-016 Biesemeyer 52Ó
T-Square
®
Home Shop Fence System.
27Ó x 46Ó White.
No. 78-928 Rear Support Table. Adds an
additional 4Õ x 4Õ of work support. White.
No. 78-925 Right Extension Table.
For use with No. 78-900 and 78-904
Biesemeyer 50Ó T-Square
®
Commercial
Fence Systems. 27Ó x 44Ó. White.
No. 78-927 Right Extension Table.
For use with No. 78-907 Biesemeyer 30Ó
Commercial Fence System. 27Ó x 24Ó
White.
No. 34-472 Extra Long Guide Bars.
Permit ripping to center of 100Ó panel.
22 lbs.
No. 34-896 Aluminum Body Jet-Lock
®
Micro-Set
®
Rip Fence. 20 lbs.
No. 34-412 “See-Thru” Splitter-Mounted
Blade Guard. Complete with spring-loaded
anti-kickback fingers. 6 lbs.
No. 36-659 Arbor Nut Assembly. Two-
piece arbor nut set provides convenient
installation and removal of the flange and
arbor nut.
For 10Ó Contractor’s Saw
®
(cont’d)
No. 34-278 Switch Kit.
Replaces toggle switch
with large, up-front
paddle switch.
No. 50-220 Dust
Connector. Attaches to
underside of saw mount-
ed to No. 50-314 Stand. 5˝ dia. outlet.
Includes mounting screws.
† No. 50-277 Mobile Base. Adds roll-away
portability to 10Ó Contractor’s Saw.
† NOTE: For saws equipped with 30˝ Unifence Saw Guide,
also order No. 50-285 Mobile Base Extension.
For 10Ó Contractor’s Saw
®
&
10Ó Contractor’s Saw
®
II
No. 50-176 Dust Bag.
Mounts easily to the underside of Delta 10˝
Contractor’s Saw and 10˝ Contractor’s Saw II
for collecting dust and chips.
No. 50-390 Outfeed Support Table Kit. For
Delta 34-444 and 34-445 10Ó Contractor’s
Saws. Includes mounting hardware and
instructions for assembling your own folding
outfeed support table. Less Support table.
No. 50-393 Outfeed Support Table Board.
For use with 50-390 Outfeed Support Table
Kit. Table board provides an additional 15
3
⁄4Ó
of work support. Medium density fiberboard.
For 10Ó Table Saws
(36-600 and 34-670)
No. 50-391 Outfeed Support Table Kit.
Includes mounting hardware and instruc-
tions for assembling your own folding
outfeed support table. Less Support table.
No. 50-394 Outfeed Support Table Board.
For use with 50-391 Outfeed Support Table
Kit. Table board provides an additional 14Ó
of work support. Medium density fiberboard.
No. 36-601 T-Square Fence System.
Upgrade your Model 34-670 10˝ Table Saw
with our newest precision fence system.
Includes rails and mounting hardware..
No. 50-279 Mobile Base. Adds roll-away
portability to 10Ó Table Saws.
For 10Ó Table Saw (34-670)
No. 34-674 Drive Belt. For replacement use
on model 34-670 10Ó Table Saw.
For All Table Saws
No. 11-400 Getting
the Most Out of Your
Table Saw. Contains a
wealth of information –
the many jobs you can
handle, types of opera-
tions that can be per-
formed using acces-
sories, safety consider-
ations and lots more.
For 10Ó Bench Saw
No. 36-541 Extension Kit. Includes one
16Ó x 8Ó die cast aluminum extension wing
with mounting hardware to increase work
support surface to a full 17
1
Ú4Ó x 34Ó.
No. 36-519 Steel Stand. Converts bench
saw to table saw height of 39Ó.
For 10Ó Contractor’s Saw
®
II
No. 36-633 Dust Collector Connector.
Mounts directly to saw carriage. 4Ó dia. outlet.
No. 36-634 Mounting Hook Kit. Includes
brackets to hold miter gage, rip fence and
wrenches.
† No. 50-286 Mobile Base. Adds roll-away
portability to 10Ó Contractor’s Saw II.
No. 78-964 Biesemeyer T-Square
®
Anti-
Kickback Snap-In Spreader. Complete with
spring-loaded anti-kickback fingers. 6 lbs.
† NOTE: For saws equipped with 30˝ Unifence Saw Guide,
also order No. 50-285 Mobile Base Extension.
For Sidekick
®
8
1
Ú4Ó Builder’s Saw
®
No. 36-276 Dado Head Table Insert.
No. 36-277 Steel Stand. Converts bench
saw to floor model machine.
No. 36-278 Table Insert.
No. 36-279 Extension Kit. Includes one 6
1
⁄4Ó
x 20" extension wing with for use on the right
or left side. With mounting hardware.
To Next Page
Loading...
