What to do if Delta ASD-A2-5543 show Wrong setting of E-gear ratio?
If your Delta Servo Drives are showing the wrong setting of E-gear ratio because setting of E-gear ratio is wrong when power on the servo drive, modify the range of E-gear ratio and repower on the servo drive.
What causes overspeed in Delta ASD-A2-5543 Servo Drives?
Overspeed in Delta Servo Drives can be triggered by: * Unstable speed input command (too much fluctuation). If this is the case, ensure that input command frequency is stable (not fluctuate too much) and activate filter function. * Defective over-speed parameter setting. If this is the case, correctly set over-speed parameter setting (P2-34).
What causes CANbus error on Delta ASD-A2-5543 Servo Drives?
A CANbus error on Delta Servo Drives is caused by CANbus off or Error Rx/Tx Counter exceeding 128. NMT Maser send “Reset node“ command to its slave or restart the servo drive.
How to fix IGBT Overheat in Delta Servo Drives?
If your Delta Servo Drives are showing IGBT Overheat, consider the following: * The drive is experiencing continuous excessive use beyond its rated loading: Increase the motor capacity or reduce the load. * The drive output is short-circuit: Ensure correct wiring.
What to do if Delta Servo Drives show Encoder voltage error or the internal of the encoder is in error?
If your Delta Servo Drives are showing encoder voltage error or the internal of the encoder is in error: * Battery voltage is too high: According to the procedure of Over voltage to check. When corrective actions are done, AL.028 will be cleared automatically. * The internal encoder is in error: If the situation is not improving, please send the drive back to the distributors or contact with Delta.
How to resolve a serial communication timeout on Delta ASD-A2-5543?
A serial communication timeout on Delta Servo Drives can occur if: * The setting value in the timeout parameter is not correct. If this is the case, correctly set P3-07. * Communication command is not being received for a long time. If this is the case, tighten the communication cable, make sure the communication cable is not damaged and ensure all wiring is correct.
What to do if CANopen PDO object does not support PDO on Delta ASD-A2-5543 Servo Drives?
If the specified object in the message does not support PDO, NMT Maser send “Reset node“ command to its slave or reset the fault by sending the control word (0x6040) through CAN communication (the value of CANopen object 0x6040 should be reset).
What to do if Delta Servo Drives show abnormal pulse command?
If your Delta Servo Drives are showing an abnormal pulse command, it could be because the pulse command frequency is higher than the rated input frequency. Correctly set the input pulse frequency.
What to do if Delta Servo Drives show The multi-turn of absolute encoder overflows?
If your Delta Servo Drives are showing that the multi-turn of absolute encoder overflows because the operation distance exceeds the range the absolute encoder is able to record, conduct homing procedure again.
What causes excessive deviation in Delta ASD-A2-5543?
Excessive deviation in Delta Servo Drives can be caused by: * Maximum deviation parameter setting is too small. If this is the case, increase the parameter setting value of P2-35. * Gain value is too small. If this is the case, correctly adjust gain value. * Torque limit is too low. If this is the case, correctly adjust torque limit value. * There is an overload. If this is the case, reduce external applied load or re-estimate the motor capacity.
General| Brand | Delta |
|---|---|
| Model | ASD-A2-5543 Series |
| Category | Servo Drives |
| Language | English |
Check product for damage, loose screws, and ensure correct wiring and power supply specifications.
Proper mounting orientation, ventilation clearance, and precautions against parallel connection to prevent damage.
Recommended circuit breakers and fuses for 220V and 400V series servo drives, recognized by UL/CSA.
Specifications for built-in and external regenerative resistors for 220V and 400V series servo drives.
Details on connecting peripheral devices, connectors, and terminals for the 220V series servo drive.
Details on connecting peripheral devices, connectors, and terminals for the 400V series servo drive.
Basic wiring diagrams for 220V series (200W and below, 400W-4.5kW, 5.5kW-15kW) and 400V series.
Provides standard wiring examples for various control modes like PT, PR, Speed, Torque, and Communication.
Provides standard wiring examples for various control modes like PT, PR, Speed, Torque, and Communication for the 400V series.
Step-by-step guide to switching between modes (Parameter, Monitoring, Alarm) and setting parameters.
Procedure for applying power, ensuring correct wiring, and understanding servo drive status indicators.
Step-by-step guide for performing a JOG trial run without load using software or DI settings.
Comprehensive guide to tuning, including inertia estimation, auto tuning, semi-auto tuning, and resonance suppression.
Lists and describes parameters for target speed, acceleration/deceleration time, pause time, PR parameters, and PR definition.
Provides a comprehensive list of parameters, their abbreviations, functions, default values, and related sections.
Detailed descriptions of various parameters, categorized into Monitor, Filter/Resonance, Gain, Position, Speed, Torque, and Communication parameters.
Lists and describes various alarms related to servo drive operation, including causes and corrective actions.
Provides detailed information on common causes of errors and step-by-step corrective actions for specific alarms.
Lists corrective actions for various alarm codes, including turning DI.ARST on or re-powering the servo drive.
Detailed specifications for ASDA-A2 220V and 400V series servo drives, covering power, control, and environmental aspects.
Specifications for ECMA series servo motors, including 220V and 400V series, with details on inertia and brake features.
Guides on system initialization, including procedures for power-on, coordinate system reset, and reading absolute coordinate data.
Guidelines for product use, storage, periodic cleaning, and avoiding disassembly of mechanical parts.
To Next Page
