Delta M60U

130 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Remove name plate cover

If there is needed to monitoring or setting the display, please follow procedure below.

CAUTION !

②

①

① Separate the large plate.

② Pull out the large plate.

Loose two screws.

Start monitoring or using the

display.

Installation

37

Table of Contents

Default Chapter3
- Table of Contents3
1 Safety10
- Information of the Inverter10
- Legal Provisions10
- Target Group10
- General Safety11
- Condition of Use11
- Symbols12
2 Introduction14
- Valid Model14
- Product Overview15
3 Installation24
- Mechanical Installation24
- Vertical Wall Mount24
- Horizontal or Tilt Mount25
- Mounting Bracket27
  - New Models with New Version of Mounting Bracket28
  - Old Models with New Version of Mounting Bracket30
- Accessories35
- 120 Models42
  - AC Wiring for M80/60U44
- 121 Models (with RSD)44
- AC Wiring for M80/60U Models (Without RSD)45
- 121 Models50
4 Commissioning64
- Display Operation Introduction64
- First Startup66
- Home Page67
- Main Menu67
- Power Meter68
  - 122 )68
- Energy Log69
5 Maintenance83
- Removing and Re-Installing the Wiring Box (WB) Cover83
- Removing the WB Cover84
- Re-Installing the WB Cover84
- Replacement of Surge Protection Devices (SPD)85
- Replace Internal String Fuse90
- Smart Fans Replacement and Filter Cleaning94
- Wiring Box (WB) Compartment Fan97
- Power Module (PM) Fan Tray98
- PM Fan Tray Removal Procedure98
- Procedures to Remove PM Air Inlet Filter100
- Release AFCI Fault Protection100
- Commissioning101
6 Error Message and Trouble Shooting103
- Error Codes103
- Warning Codes104
- Fault Codes105
- Calling for Help109
- Service Call Checklist109
7 Technical Information110
- Technical of M80U Series110
- Technical of M60U Series113
Appendix A-1: Low and High Voltage Ride-Through Set-Points and Timing Per Table SA9.1D116
Appendix A-2: Low and High Frequency Ride-Through Set-Points and Timing Per Table SA10.1116
APPENDIX: Grid Support Utility Interactive Inverters116
- Appendix A: Rule 21116
Appendix A-3: CA R21 Settings - Normal Ramp Rate (RR) & Soft-Start Ramp Rate (SS)117
Appendix A-4: CA R21 Settings - Soft-Start Ramp Rate Test117
Appendix A-5: CA R21 Settings - Specified Power Factor117
Appendix A-6: CA R21 Settings - Volt/Var Mode (Q(V))118
Appendix A-7: CA R21 Settings - Frequency-Watt (FW)118
Appendix A-8: CA R21 Settings - Volt-Watt (VW)119
Appendix B-1: Full Frequency Ride-Through Settings for O'ahu, Hawai'I Island, and Maui (HECO A)120
Appendix B-2: Full Frequency Ride-Through Settings for Moloka'I and Lana'I (HECO B)120
Appendix B-3: Full Voltage Ride-Through Settings for O'ahu, Hawai'I Island, Maui, Moloka'I, and Lana'I120
- Appendix B: HECO120
Appendix C-1: Assembly Note for All Model123
Appendix C: Assembly Note123
Appendix C-2: Assembly Note for 120 Model124
Appendix C-3: Assembly Note for 121 Model (with RSD)125
Appendix C-4: Assembly Note for 121 Model (Without RSD)126
Appendix C-5: Assembly Note for 122 Model127

Related product manuals

Preview: Delta RPI M6A

Preview: Delta M70A

Preview: Delta M80U

Preview: Delta RPI-M8

Preview: Delta M Series

Preview: Delta RPI-M15A

Preview: Delta RPI M50A

Preview: Delta M30A 230

Preview: Delta M100A 283

Delta M100A 283