To Next PageTo Next Page
Need help?Do you have a question about the Delta VFD25AMS43ANSHA and is the answer not in the manual?
General| Model | VFD25AMS43ANSHA |
|---|---|
| Category | Controller |
| Brand | Delta |
| Output Current | 25A |
| Power Rating | 11 kW |
| Frequency Range | 0.1 - 400 Hz |
| Cooling Method | Fan Cooling |
| Altitude | Up to 1000m without derating |
| Enclosure Rating | IP20 |
| Communication Interface | RS-485 |
| Input Voltage | 3-phase 380-480V AC |
| Control Method | V/F control, Sensorless Vector Control |
| Communication Protocol | Modbus |
| Protection Features | Overload, Overvoltage, Undervoltage, Overheating |
| Operating Temperature | -10°C to +50°C |
| Storage Temperature | -20°C to 60°C |
| Humidity | 5% to 95% (non-condensing) |
Guidelines for minimum mounting clearances and installation requirements.
General wiring instructions for AC motor drives, including safety precautions.
Illustrates the system wiring diagram for AC motor drives, detailing component connections.
Provides a schematic diagram of the main circuit connections for the AC motor drive.
Details on selecting applicable brake resistors and brake units for improved drive performance.
Step-by-step instructions for installing option cards into the AC motor drive.
Details features, profile, specifications, and communication parameters for the MODBUS TCP option card.
Provides features, profile, specifications, and connector pin assignments for the PROFIBUS option card.
Details functions, profile, specifications, and LED indicators for the DeviceNet option card.
Covers features, profile, specifications, and communication parameters for the EtherNet/IP option card.
Details product profile, RJ-45 pin definition, specifications, and CANopen communication cable.
Provides detailed specifications for 230V series AC motor drives, including 1-phase and 3-phase models.
Provides detailed specifications for 460V series AC motor drives, including 3-phase models.
Details environmental conditions for operation, storage, and transportation, including temperature and humidity.
Provides derating curves for ambient temperature and altitude affecting output current rating.
Explains the functions and displays of various keypad buttons and items.
Details the step-by-step process for operating the keypad, including main page selection and parameter setting.
Details protection parameters for malfunctions like output frequency, DC voltage, and IGBT temperature.
Details drive parameters including identity codes, rated current, and parameter reset options.
Covers basic parameters like max operation frequency, output voltage, and mid-point settings for motors.
Explains digital input/output parameters, including operation control modes and multi-function terminals.
Details analog input/output parameters like selection, gain, bias, and filter times.
Details protection parameters for low voltage, over-voltage stall prevention, and over-current stall prevention.
Covers special parameters like software brake, DC brake, restart after fault, and dEb function.
Details communication parameters for RS-485, CANopen, and DeviceNet, including address and speed settings.
Corrective actions for Modbus function code errors, emphasizing function code correctness.
Corrective actions for Modbus data address errors, focusing on communication address correctness.
Corrective actions for Modbus data errors, advising to check data value against max/min.
Corrective actions for IGBT overheating, focusing on ambient temperature and ventilation.
Corrective actions for over-current during acceleration, including checking motor output and drive power.
Corrective actions for over-current during deceleration, focusing on acceleration time and drive power.
Corrective actions for over-current during steady state operation, checking motor output and drive power.
Description of short circuit at motor output and corrective actions.
Corrective actions for DC-BUS over-voltage, including checking input voltage and regenerative voltage.
Corrective actions for DC-BUS over-voltage during deceleration, suggesting increased deceleration time.
Corrective actions for low DC-BUS voltage during acceleration.
Corrective actions for low DC-BUS voltage during deceleration.
Corrective actions for phase loss in 3-phase or 1-phase applications.
Corrective actions for IGBT overheating, focusing on ambient temperature and ventilation.
Corrective actions for overload, suggesting checking motor loading or higher power model.
Corrective actions for motor overheating, checking obstructions and ambient temperature.
Over-torque detection behavior based on Pr. settings, detailing warning vs. error outputs.
Describes external fault condition and corrective actions.
Describes emergency stop condition and corrective actions.
Lists CANopen fault codes, their descriptions, and corresponding fault registers.
Steps for connecting to PC and implementing PLC functions on the MS300.
Provides guidance on handling and recommended approaches for various PLC error codes.
Provides a basic description of the MS300 Safe Torque Off (STO) function and its international specifications.
Describes the terminal functions related to STO, including signal inputs and action logic.
Illustrates wiring diagrams for the safe control loop, including internal circuits and external connections.
Provides descriptions for STO relevant error codes and their corresponding corrective actions.
Step-by-step instructions to check the normal operation of STO and related detection functions.
