Denon AVR-1403 - User Manual

Other manuals for Denon AVR-1403

Service Manual6 pages

Owner's Manual28 pages

Product Sheet2 pages

Questions and Answers:

R
Roy PetersJul 30, 2025
Why is there no sound coming from my Denon AVR-1403 even though the display is on?
- J
  Justin OlsonJul 30, 2025
  There might be several reasons why your Denon Stereo Receiver display is lit but no sound is produced: * The speaker cords might not be securely connected, so ensure they are properly connected. * The audio function button may be in an incorrect position; adjust it to a suitable setting. * The volume control might be set to the minimum; increase the volume to an audible level. * MUTING might be activated; switch MUTING off. * If you've selected a digital input, ensure digital signals are being input or select the correct input jacks.
D
Destiny FranklinAug 3, 2025
How to fix a Denon Stereo Receiver when the display is off and there is no sound when the power switch is on?
- R
  rebeccaibarraAug 3, 2025
  If the display is not lit and no sound is produced when the power switch is set to on, check that the power cord is securely plugged in. If this doesn't solve the issue, turn the power off with the remote control unit after turning the POWER operation switch on.
M
murphymariaAug 9, 2025
What to do if my Denon AVR-1403 Stereo Receiver isn't responding to the remote control?
- A
  Adam ReeseAug 9, 2025
  If your Denon Stereo Receiver isn't responding to the remote control, consider these potential solutions: 1. The batteries in the remote might be dead. Replace them with new ones. 2. You might be too far from the unit. Move closer to the receiver. 3. There could be an obstacle blocking the signal. Remove any obstructions between the remote and the receiver. 4. You might be pressing the wrong button. Ensure you're pressing the correct button for the desired function. 5. The batteries might be inserted incorrectly. Check that the + and - ends of the batteries are properly aligned.
E
Erik MooreAug 14, 2025
Why is the 'ON/STANDBY' LED flashing rapidly and the display not showing on my Denon AVR-1403?
- L
  Luis LewisAug 14, 2025
  If the display isn't showing and the 'ON/STANDBY' LED is flashing rapidly on your Denon Stereo Receiver, it could be due to a few reasons: * The speaker terminals may be short-circuited. Turn off the power, properly connect the speakers, and then turn the power back on. * The ventilation holes of the set might be blocked. Turn off the power, ensure adequate ventilation to cool it down, and then turn the power back on. * The unit might be operating at continuous high power with inadequate ventilation. Turn off the power, ventilate well to cool it down, and then turn the power back on.
S
Stacy WhiteAug 19, 2025
What to do if sound is only coming from one channel on my Denon AVR-1403?
- A
  Amber MartinezAug 19, 2025
  If sound is only coming from one channel on your Denon Stereo Receiver, it may be caused by: * Incomplete connection of speaker cords. Connect them securely. * Incomplete connection of input/output cords. Ensure they are securely connected.
K
Kristi MedinaAug 25, 2025
Why are the instruments reversed during stereo playback on my Denon AVR-1403 Stereo Receiver?
- K
  kevin62Aug 25, 2025
  If the positions of instruments are reversed during stereo playback on your Denon Stereo Receiver, the left and right speakers, or the left and right input/output cords, might be connected in reverse. Check the left and right connections to resolve this.

Denon AVR-1403 Specifications

General

Channels	5.1
Total Harmonic Distortion (THD)	0.08%
Frequency Response	10 Hz - 100 kHz (+1, -3 dB)
Input Sensitivity	200 mV
Signal-to-Noise Ratio	98 dB
Digital inputs	2 Optical, 1 Coaxial
Input Impedance	47 kOhms
Type	AV Receiver
Power Output (per channel)	75W (8 ohms, 20Hz-20kHz, 0.08% THD)
Video Inputs	3 x Composite
Tuner Frequency Range	FM: 87.5 - 108 MHz