To Next PageTo Next Page
How do I get Dolby TrueHD, DTS-HD, or Dolby Digital Plus audio to output on my Denon Stereo Receiver?
First, ensure that the HDMI is properly connected. Check that the Blu-ray Disc player’s audio output setting is set to bitstream. If you're using DTS, make sure your Blu-ray Disc player is compatible with DTS sound playback.
How do I fix no sound from the center speaker on my Denon Stereo Receiver?
If you are playing a monaural source in “STANDARD” mode, change the mode to something other than “STANDARD” (Dolby/DTS Surround).
How to fix no sound from surround speakers on Denon Stereo Receiver?
If the surround mode is set to “STEREO” or “DIRECT”, change it to a surround playback mode.
Why is there no sound from the subwoofer on my Denon Stereo Receiver?
First, ensure the subwoofer is powered on. Check that the “Subwoofer” setting at “Speaker Config.” is set to “Yes.” Verify the connections to the subwoofer are correct. Finally, adjust the subwoofer’s volume to an appropriate level, ensuring it’s not turned off.
Why is there no sound from surround back speaker on my Denon Stereo Receiver?
Ensure the pre-out assignment for the surround back speakers is correctly set. Verify that the “S.Back” setting is not set to “None.” Check that the “Parameter” – “Surround Parameter” – “SB CH Out” settings are not “OFF.” Finally, select a surround playback mode that supports 6.1- or 7.1-channel playback.
Why does my Denon Stereo Receiver have no sound?
Several factors could cause a lack of sound from your Denon Stereo Receiver speakers. First, check the connections to your input devices and speaker cables to ensure they are secure. Then, verify that the input source selected on the receiver matches the device you're trying to play. Also, make sure the master volume isn't set too low and that mute mode is off. Disconnect any connected headphones, as they may be diverting the audio. If using digital inputs, confirm that digital signals are being input and that the input mode is correctly set.
Why is the display off on my Denon Stereo Receiver?
If the “Display” setting is set to “OFF”, change it to something other than “OFF.”
Why can't I see the menu screen and status indicators on my Denon Stereo Receiver?
If the display status is set to “OFF”, press the MENU button on the main unit or remote control. If the main volume display is “OFF”, set “Manual Setup” – “Option Setup” – “On-Screen Display” – “Text” to “ON.” For tuner operation, set “Manual Setup” – “Option Setup” – “On-Screen Display” – “Master Volume” to “Top” or “Bottom.” For iPod operation, ensure “Manual Setup” – “On-Screen Display” – “Tuner Information” and “Manual Setup” – “On-Screen Display” – “ iPod Information” are not set to “OFF.”
Why is there no picture appearing on my Denon AVR-590 Stereo Receiver?
Check the connections between the AVR-590 and the monitor to ensure they are secure. Verify that the monitor's input setting is correct. If using component input connectors with video output connectors, set the player to interlace (480i/576i) signals, as high-definition signals are not down-converted.
Why doesn't my Denon Stereo Receiver remote control work properly?
Several reasons may cause the remote control to malfunction. First, replace the batteries with new ones. Ensure you are operating within the specified range and that there are no obstacles between the remote and the main unit. Check that the batteries are inserted correctly, following the polarity marks. Move the set away from strong light sources that might interfere with the remote control sensor. Also, make sure the device selection switch and device mode are properly set for the device you are trying to operate.
General| Channels | 5.1 |
|---|---|
| Power Output | 75 W per channel (8 ohms, 20Hz-20kHz, 0.08% THD) |
| HDMI Inputs | 4 |
| HDMI Outputs | 1 |
| Signal-To-Noise Ratio | 98 dB |
| THD | 0.08% |
| Input Impedance | 47 kOhm |
| Input Sensitivity | 200 mV |
| Surround System Class | 5.1 channel |
| HDMI Switching | Yes |
| 3D Technology | Yes |
| Input Sensitivity/Impedance | 200 mV / 47 kOhm |
| HDMI Version | 1.3a |
| Dolby Formats | Dolby Digital, Dolby Digital Plus |
| DTS Formats | DTS, DTS Neo:6, DTS 96/24 |
| Audyssey | MultEQ |
| Amplifier Output Details | 75 W per channel at 8 ohms, 20 Hz to 20 kHz, 0.08% THD |
| Response Bandwidth | 10Hz - 100kHz |
| Audio D/A Converter | 192 kHz/24-bit |
| Frequency Response | 10 Hz to 100 kHz |
| Video Inputs/Outputs | Composite, Component |
| Audio Inputs/Outputs | Digital Optical |
