To Next PageTo Next PageHow to fix reception failures on my Denon AVR-1713?
Try changing the antenna's orientation or position. Consider using an FM outdoor antenna. Also, keep the antenna separate from other connection cables.
Why does my Denon AVR-1713 Receiver automatically switch to standby mode?
Your Denon Receiver might be automatically switching to standby mode because: * The sleep timer is set. You can turn the power back on or adjust the sleep timer settings. * The “Auto Standby” feature is activated due to inactivity. To disable it, set “Auto Standby” to “Off” in the menu.
Why is the power indicator blinking red on my Denon Receiver?
Ensure you are using speakers with the specified impedance. The protection circuit might be activated because the speaker cable core wires are touching, a core wire has come loose, or a core wire is touching the rear panel. Unplug the power cord and correct any wiring issues, then reconnect the wire.
What does it mean when the power indicator is blinking red on my Denon AVR-1713?
If the power indicator on your Denon Receiver is blinking red at approximately 0.5-second intervals: * Ensure that you are using speakers with the specified impedance. * The protection circuit has been activated. This might be due to speaker cable core wires touching, a core wire coming loose, or a core wire touching the rear panel. Unplug the power cord, correct the wiring issues (re-twist wires, secure terminals), and then reconnect the power.
Why can't I log in to Pandora on my Denon Receiver?
The login information may be incorrect. Check that the “Email address” for Pandora has been entered correctly and re-enter the “Password”.
How to output DTS sound on my Denon AVR-1713?
Set “Decode Mode” on the menu to “Auto” or “DTS”.
Why is the AirPlay icon not displayed for my Denon AVR-1713 in iTunes or on my iPhone/iPod touch/iPad?
If the AirPlay icon is missing in iTunes or on your iPhone/iPod touch/iPad when trying to connect to your Denon Receiver: * Ensure that your device and the receiver are connected to the same network (LAN). * Make sure iTunes or your iPhone/iPod touch/iPad has the latest firmware that supports AirPlay installed.
Why is there no audio output with HDMI connection on my Denon AVR-1713 Receiver?
First, verify the HDMI connectors are properly connected. If you want audio from the speakers, ensure “HDMI Audio Out” is set to “AVR” in the menu. If you want audio from the TV, set “HDMI Audio Out” to “TV” in the menu.
Why is there no video output with HDMI connection on my Denon Receiver?
If you're not getting any video output via HDMI on your Denon Receiver, consider the following: * Check the HDMI cable connections to ensure they are properly connected. * Make sure the input source on the receiver matches the HDMI connector you're using. * Verify that your TV is compatible with HDCP (High-bandwidth Digital Content Protection). If the connected device isn't HDCP-compliant, the video may not display correctly.
How to fix audio not outputting on my Denon AVR-1713?
Check the connections for all devices and the speaker connections and configurations. Verify that the audio device is powered on, and adjust the master volume. Also, ensure mute mode is off. Check the connection with the playback device and select the correct input source. Match the input mode and the assigned digital input terminal. Disconnect headphones, as no sound is output from the speakers when headphones are connected.
General| Receiver type | - |
|---|---|
| Audio output channels | 5.1 channels |
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Power output per channel (1KHz@6 Ohm) | 120 W |
| Power output per channel (20-20KHz@8 Ohm) | 80 W |
| HDMI in | 5 |
| Composite video in | 2 |
| Digital audio optical in | 1 |
| Ethernet LAN | Yes |
| Preset stations quantity | 56 |
| Internet radio services supported | Last.fm |
| Supported video modes | 1080p |
| Analog signal format system | NTSC, PAL |
| Display | LCD |
| HDMI version | 1.4 |
| Product color | Black |
| Audio decoders | Dolby Pro Logic II, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-HD |
| Apple docking compatibility | Not supported |
| Graphical user interface (GUI) language | English, French, German |
| AC input voltage | 220-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 0.5 W |
| Storage temperature (T-T) | -10 - 60 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Storage relative humidity (H-H) | 5 - 90 % |
| Operating relative humidity (H-H) | 10 - 80 % |
Weight and Dimensions| Depth | 332 mm |
|---|---|
| Width | 435 mm |
| Height | 151 mm |
| Weight | 8300 g |
