Denon AVR-1713 - Service Manual

Other manuals for Denon AVR-1713

Owner's Manual156 pages

Getting Started10 pages

Specifications2 pages

Questions and Answers

J
Joshua HunterSep 2, 2025
What to do if there is no audio output from my Denon Receiver?
- P
  Peggy LeeSep 2, 2025
  If you are experiencing a lack of audio output from your Denon Receiver, here are some things to check: * Ensure all device connections are secure. * Verify speaker connections and configurations. * Confirm the audio device is powered on. * Adjust the master volume. * Deactivate mute mode. * Check the connection with the playback device and select the appropriate input source. * Match the input mode and the terminal assigned to be the digital input terminal. * Disconnect any connected headphones, as this will prevent sound from the speakers.
M
Mark SimpsonSep 1, 2025
How to fix audio not outputting on my Denon AVR-1713?
- N
  Nicole MartinezSep 1, 2025
  Check the connections for all devices and the speaker connections and configurations. Verify that the audio device is powered on, and adjust the master volume. Also, ensure mute mode is off. Check the connection with the playback device and select the correct input source. Match the input mode and the assigned digital input terminal. Disconnect headphones, as no sound is output from the speakers when headphones are connected.
J
James HallAug 31, 2025
What to do if no sound is produced from the subwoofer of my Denon AVR-1713 Receiver?
- S
  sotojenniferAug 31, 2025
  First, check the subwoofer connections and make sure the subwoofer is powered on. Then, in the menu, set “Speaker Config.” – “Subwoofer” to “Yes”. If “Front” and “Center” are set to “Large” and “Subwoofer Mode” is set to “LFE”, no sound may be output depending on the input signal or selected sound mode.
A
Ann MedinaAug 30, 2025
What to do if my Denon AVR-1713 Receiver power does not turn on?
- F
  fsullivanAug 30, 2025
  Check that the power plug is correctly inserted into the power outlet. If it is, the protection circuit might be active. Unplug the power cord, wait 5 to 10 seconds, and then plug it back in.
K
krobinsonAug 29, 2025
Why is the sound broken during playback on my Denon AVR-1713 Receiver?
- J
  Jennifer AcostaAug 29, 2025
  If the sound breaks during playback on your Denon Receiver, it may be due to a slow network or USB memory device signal transfer speed, congested communication lines, or a congested radio station. This isn't a malfunction. When playing broadcast data with a high bit rate, the sound may break depending on communication conditions.
J
Jennifer FloresAug 28, 2025
Why is the volume not increasing on my Denon AVR-1713?
- J
  Justin SmithAug 28, 2025
  If the volume on your Denon Receiver isn't increasing as expected: * The maximum volume might be set too low. Adjust the maximum volume using the “Limit” setting in the menu. * External devices connected to the unit's output connectors may not be powered on. Check the power status of these devices.
L
Lauren WigginsAug 27, 2025
Why is the display off on my Denon AVR-1713?
- B
  Benjamin WhiteheadAug 27, 2025
  If the display on your Denon Receiver is off, set “Dimmer” on the menu to something other than “Off”.
S
Stephanie BarryAug 26, 2025
What does it mean when the power indicator is blinking red on my Denon AVR-1713?
- C
  carolfoxAug 27, 2025
  If the power indicator on your Denon Receiver is blinking red at approximately 0.5-second intervals: * Ensure that you are using speakers with the specified impedance. * The protection circuit has been activated. This might be due to speaker cable core wires touching, a core wire coming loose, or a core wire touching the rear panel. Unplug the power cord, correct the wiring issues (re-twist wires, secure terminals), and then reconnect the power.
M
Mackenzie McdonaldAug 25, 2025
Why is the power indicator blinking red on my Denon Receiver?
- S
  Sarah JenkinsAug 26, 2025
  Ensure you are using speakers with the specified impedance. The protection circuit might be activated because the speaker cable core wires are touching, a core wire has come loose, or a core wire is touching the rear panel. Unplug the power cord and correct any wiring issues, then reconnect the wire.
J
Jacqueline GillAug 25, 2025
Why does my Denon AVR-1713 Receiver automatically switch to standby mode?
- L
  Lisa ReeseAug 25, 2025
  Your Denon Receiver might be automatically switching to standby mode because: * The sleep timer is set. You can turn the power back on or adjust the sleep timer settings. * The “Auto Standby” feature is activated due to inactivity. To disable it, set “Auto Standby” to “Off” in the menu.

Denon AVR-1713 Specifications

General

Receiver type	-
Audio output channels	5.1 channels
Audio A/D Converter (ADC)	24-bit/96kHz
Power output per channel (1KHz@6 Ohm)	120 W
Power output per channel (20-20KHz@8 Ohm)	80 W
HDMI in	5
Composite video in	2
Digital audio optical in	1
Ethernet LAN	Yes
Preset stations quantity	56
Internet radio services supported	Last.fm
Supported video modes	1080p
Analog signal format system	NTSC, PAL
Display	LCD
HDMI version	1.4
Product color	Black
Audio decoders	Dolby Pro Logic II, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-HD
Apple docking compatibility	Not supported
Graphical user interface (GUI) language	English, French, German
AC input voltage	220-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.5 W
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 80 %