Denon AVR-1905 User Manual (English)

Other manuals for Denon AVR-1905

Operating Instructions77 pages

Brochure & Specs2 pages

Questions and Answers:

M
Mr. Mark Peterson Jr.Aug 20, 2025
Why does my Denon AVR-1905 have no sound but the display is on?
- K
  Katherine MendozaAug 20, 2025
  If the display is lit on your Denon Stereo Receiver but you're not getting any sound, check the following: * Ensure the speaker cords are securely connected. * Verify the audio function button is in the correct position. * Make sure the volume isn't set to the minimum. * Confirm that MUTING is switched off. * If using digital signals, ensure they are being input correctly and the correct input jacks are selected.
B
Brittany JohnsonAug 22, 2025
Why is sound only coming from one speaker on my Denon AVR-1905 Stereo Receiver?
- H
  heather40Aug 22, 2025
  If sound is only coming from one channel on your Denon Stereo Receiver, it's likely due to: * An incomplete connection of the speaker cords. Connect them securely. * An incomplete connection of the input/output cords. Ensure they are securely connected.
C
Clifford NorrisAug 25, 2025
What to do if my Denon Stereo Receiver display is lit but no sound is produced?
- V
  Vincent WilsonAug 25, 2025
  If the display is lit but no sound comes out of your Denon Stereo Receiver, consider these potential causes: * Speaker cords might not be securely connected; ensure they are properly connected. * The audio function button may be improperly positioned; adjust it to a suitable setting. * The volume control might be set to the minimum; increase the volume to an audible level. * MUTING may be activated; switch MUTING off. * If you've selected a digital input, ensure digital signals are being input, or select the correct input jacks.
L
Lori ProctorAug 26, 2025
How to fix a Denon Stereo Receiver when the display is not lit and no sound is produced?
- E
  Elizabeth DominguezAug 27, 2025
  If the display isn't lit and no sound is produced when the power switch is on, check that the power cord is securely plugged in. If it is, try turning the power on with the remote control after switching the POWER switch on.
B
brianherringAug 27, 2025
What to do if my Denon Stereo Receiver remote is not working?
- R
  Rodney MendozaAug 27, 2025
  If your Denon Stereo Receiver isn't responding to the remote, try these steps: * First, replace the batteries with new ones. * Make sure you're close enough to the unit. * Remove any obstacles blocking the remote's signal. * Ensure you're pressing the correct button. * Verify the batteries are inserted with the correct polarity.
H
hwashingtonAug 29, 2025
What to do if the Denon AVR-1905 Stereo Receiver display is off and the power light is flashing?
- R
  Richard KochAug 29, 2025
  If the display on your Denon Stereo Receiver is not lit and the power indicator is flashing rapidly, it usually indicates a short circuit or overheating. Here's what to do: * Switch the power off, properly connect the speakers, and then switch the power back on if speaker terminals are short-circuited. * If the ventilation holes are blocked or the unit is overheating, turn off the power, ventilate well to cool it down, and then turn the power back on once it's cooled.
M
Michael PerezAug 31, 2025
Why won't my Denon AVR-1905 turn on?
- G
  Gavin HarrisAug 31, 2025
  If your Denon Stereo Receiver's display isn't lit and no sound is produced when the power switch is on: * Check that the power cord is securely plugged in. * After turning the POWER switch on, turn the power on with the remote control unit.
J
Jonathan StuartSep 2, 2025
How to stop humming noise on Denon Stereo Receiver when playing records?
- I
  ibrownSep 2, 2025
  If you're hearing a humming noise when playing records on your Denon Stereo Receiver, it could be due to: * An improperly connected turntable ground wire. Connect it securely. * An incomplete PHONO jack connection. Ensure it's securely connected. * Nearby TV or radio transmission antenna. Contact your store of purchase.
D
Daniel AlexanderSep 3, 2025
Why is my Denon AVR-1905 making a howling noise at high volume?
- L
  lgarzaSep 4, 2025
  If you experience howling noise from your Denon Stereo Receiver when the volume is high: * The turntable and speaker systems might be too close together. Separate them as much as possible. * An unstable floor could be the cause. Use cushions to absorb speaker vibrations transmitted by the floor. If the turntable lacks insulators, use audio insulators.
G
Gary BurnettSep 5, 2025
Why are the instruments reversed on my Denon Stereo Receiver during stereo playback?
- E
  Elizabeth StevensSep 5, 2025
  If the instrument positions are reversed during stereo playback on your Denon Stereo Receiver, it's probably due to reversed connections of the left and right speakers or input/output cords. Check the left and right connections to correct this.

Denon AVR-1905 Specifications

General

Speakers connectivity type	-
Receiver type	Surround
Frequency range	10 - 100000 Hz
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	100 dB
Power output per channel (1KHz@6 Ohm)	110 W
Power output per channel (20-20KHz@8 Ohm)	80 W
Product color	Black
Audio decoders	DTS 96/24, DTS Neo:6, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), Dolby Digital EX, Dolby Pro Logic IIx
Digital Signal Processing (DSP)	Yes
HDMI in	0
Composite video in	4
Digital audio coaxial in	1
Component video (YPbPr/YCbCr) in	3
S-Video outputs quantity	2
Ethernet LAN	No
AM band range	520 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
AC input voltage	120 V
AC input frequency	60 Hz