To Next Page
E
erik95Aug 29, 2025
Why is Dolby TrueHD, DTS-HD, Dolby Digital Plus audio not output on Denon Receiver?
- JjerryrobertsonAug 29, 2025
If your Denon Receiver is not outputting Dolby TrueHD, DTS-HD, or Dolby Digital Plus audio, make HDMI connections.
Why is Dolby TrueHD, DTS-HD, Dolby Digital Plus audio not output on Denon Receiver?
If your Denon Receiver is not outputting Dolby TrueHD, DTS-HD, or Dolby Digital Plus audio, make HDMI connections.
How to turn on display on Denon AVR-1913?
If your Denon Receiver display is off, set “Dimmer” on the menu to something other than “Off”.
What to do if Denon AVR-1913 set does not operate properly?
If your Denon Receiver set does not operate properly, try resetting the microprocessor.
How to fix no audio output with HDMI connection on Denon AVR-1913 Receiver?
If no audio is output with an HDMI connection on your Denon Receiver, try these steps: * Check the HDMI connector connections. * To output HDMI audio from the speakers, set “HDMI Audio Out” to “AVR” in the menu. * To output HDMI audio from a TV, set “HDMI Audio Out” to “TV” in the menu.
Why is the power indicator blinking red on my Denon Receiver?
If the power indicator on your Denon Receiver is blinking red in intervals of approximately 0.5 seconds, consider the following: * Ensure you are using speakers with the specified impedance. * The protection circuit may have been activated because the speaker cable core wires are touching, a core wire has come loose, or a core wire is touching the rear panel. Unplug the power cord, correct the wiring by re-twisting loose wires or securing the terminal, and then reconnect the wire.
How to troubleshoot no sound from subwoofer on Denon Receiver?
If your Denon Receiver is not producing sound from the subwoofer, check these items: * Verify the subwoofer connections. * Make sure the subwoofer is powered on. * In the menu, set “Speaker Config.” – “Subwoofer” to “Yes”. * Note that if “Front” and “Center” are set to “Large” in “Speaker Config.”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers depending on the input signal or selected sound mode.
Why does my Denon AVR-1913 power automatically switch to standby mode?
If your Denon Receiver automatically switches to standby mode, consider the following: * The sleep timer may be set. Turn the power back on or adjust the sleep timer settings. * The “Auto Standby” feature may be enabled, which activates after a period of inactivity. To disable this, set “Auto Standby” to “Off” in the menu.
General| Receiver type | - |
|---|---|
| Audio output channels | 7.1 channels |
| Power output per channel (1KHz@6 Ohm) | 125 W |
| Power output per channel (20-20KHz@8 Ohm) | 90 W |
| HDMI in | 6 |
| Audio (L/R) in | 5 |
| Composite video in | 3 |
| Component video (YPbPr/YCbCr) in | 1 |
| Audio formats supported | AAC, FLAC, MP3, WMA |
| Ethernet LAN | Yes |
| FM band range | 87.5 - 107.9 MHz |
| Supported radio bands | FM |
| Internet radio services supported | Pandora, SIRIUS Internet Radio, Spotify, vTuner |
| Card reader integrated | No |
| Supported video modes | 1080p |
| Supported graphics resolutions | 1920 x 1080 (HD 1080) |
| Product color | Black |
| Audio decoders | Dolby Digital Plus, Dolby Pro Logic IIz, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-ES (Discrete 6.1), DTS-HD, DTS-HD Master Audio |
| Volume control | Rotary |
Weight and Dimensions| Depth | 162 mm |
|---|---|
| Width | 434.3 mm |
| Height | 328.9 mm |
| Weight | 9099 g |
