Denon AVR-1913 Service Manual (English)

Other manuals for Denon AVR-1913

Service Manual222 pages

Getting Started10 pages

Questions and Answers:

D
Deborah LandrySep 13, 2025
How to fix files on USB memory device if they cannot be played on Denon AVR-1913 Receiver?
- J
  Jonathan HarrisSep 14, 2025
  If files on a USB memory device cannot be played on your Denon Receiver: * Ensure the USB memory device is formatted to FAT16 or FAT32. Refer to the USB memory device’s operating instructions for details. * If the USB memory device is divided into multiple partitions, only files in the first partition can be played. * The files may be stored in a non-compatible format. Record the files in a compatible format. * The file may be copyright protected, which prevents playback on this unit.
D
diazchristopherAug 25, 2025
Why does my Denon AVR-1913 power automatically switch to standby mode?
- D
  Dr. Sarah AllisonAug 25, 2025
  If your Denon Receiver automatically switches to standby mode, consider the following: * The sleep timer may be set. Turn the power back on or adjust the sleep timer settings. * The “Auto Standby” feature may be enabled, which activates after a period of inactivity. To disable this, set “Auto Standby” to “Off” in the menu.
C
Christina Hamilton MDAug 25, 2025
How to troubleshoot no sound from subwoofer on Denon Receiver?
- K
  Kathryn RobertsonAug 26, 2025
  If your Denon Receiver is not producing sound from the subwoofer, check these items: * Verify the subwoofer connections. * Make sure the subwoofer is powered on. * In the menu, set “Speaker Config.” – “Subwoofer” to “Yes”. * Note that if “Front” and “Center” are set to “Large” in “Speaker Config.”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers depending on the input signal or selected sound mode.
M
marc68Aug 26, 2025
Why is the power indicator blinking red on my Denon Receiver?
- J
  Jill WallaceAug 27, 2025
  If the power indicator on your Denon Receiver is blinking red in intervals of approximately 0.5 seconds, consider the following: * Ensure you are using speakers with the specified impedance. * The protection circuit may have been activated because the speaker cable core wires are touching, a core wire has come loose, or a core wire is touching the rear panel. Unplug the power cord, correct the wiring by re-twisting loose wires or securing the terminal, and then reconnect the wire.
A
Alicia FloresAug 27, 2025
How to fix no audio output with HDMI connection on Denon AVR-1913 Receiver?
- C
  Cheryl ShahAug 27, 2025
  If no audio is output with an HDMI connection on your Denon Receiver, try these steps: * Check the HDMI connector connections. * To output HDMI audio from the speakers, set “HDMI Audio Out” to “AVR” in the menu. * To output HDMI audio from a TV, set “HDMI Audio Out” to “TV” in the menu.
J
Justin AlvarezSep 8, 2025
Why Dolby PLg mode or DTS NEO:6 mode cannot be selected on Denon AVR-1913 Receiver?
- A
  ashley00Sep 8, 2025
  If you cannot select Dolby PLg mode or DTS NEO:6 mode on your Denon Receiver: * Ensure that “Speaker Config.” – “Center” or “Surround” is set to something other than “None”. This sound mode cannot be selected if the speaker system is 2.0/2.1ch. * Dolby PLg or DTS NEO:6 cannot be selected when headphones are in use.
M
Megan LeeSep 7, 2025
How to enable DTS sound output on Denon Receiver?
- T
  Thomas HuntSep 7, 2025
  If your Denon Receiver is not outputting DTS sound, set “Decode Mode” on the menu to “Auto” or “DTS”.
J
James WardSep 7, 2025
What does it mean when the power indicator is blinking red on Denon AVR-1913?
- T
  Tina MooreSep 8, 2025
  If the power indicator on your Denon Receiver is blinking red every 2 seconds, the protection circuit may have been activated due to high humidity inside the unit. Turn off the power and re-apply it after the temperature has sufficiently decreased. Also, reinstall the unit in a location with good ventilation.
H
howelllauraSep 2, 2025
How to troubleshoot no sound from front height speaker on Denon AVR-1913 Receiver?
- D
  david22Sep 2, 2025
  If there is no sound from the front height speaker on your Denon Receiver: * Check if “Amp Assign” is set appropriately to output audio from the front height speakers. * Set “Speaker Config.” – “Front Height” in the menu to something other than “None.”
R
Ricky MillsAug 31, 2025
Why the volume does not increase on Denon AVR-1913 Receiver?
- L
  Louis GutierrezAug 31, 2025
  If the volume does not increase on your Denon Receiver: * The maximum volume may be set too low. Adjust the maximum volume using “Limit” in the menu. * External devices connected to the unit's output connectors may not be powered on. Check the power status of these connected devices.

Denon AVR-1913 Specifications

General

Receiver type	-
Audio output channels	7.1 channels
Power output per channel (1KHz@6 Ohm)	125 W
Power output per channel (20-20KHz@8 Ohm)	90 W
HDMI in	6
Audio (L/R) in	5
Composite video in	3
Component video (YPbPr/YCbCr) in	1
Audio formats supported	AAC, FLAC, MP3, WMA
Ethernet LAN	Yes
FM band range	87.5 - 107.9 MHz
Supported radio bands	FM
Internet radio services supported	Pandora, SIRIUS Internet Radio, Spotify, vTuner
Card reader integrated	No
Supported video modes	1080p
Supported graphics resolutions	1920 x 1080 (HD 1080)
Product color	Black
Audio decoders	Dolby Digital Plus, Dolby Pro Logic IIz, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-ES (Discrete 6.1), DTS-HD, DTS-HD Master Audio
Volume control	Rotary