Denon AVR-2803 Operating Instructions

20
ENGLISH
3. Video deck (VCR) system
buttons
POWER : Power on/standby
(ON/SOURCE)
6,7 : Manual search
(forward and reverse)
2 : Stop
1 : Play
3 : Pause
Channel +, – : Channels
4. Monitor TV (TV), digital
broadcast satellite (DBS)
tuner and cable (CABLE)
system buttons
POWER : Power on/standby
(ON/SOURCE)
MENU : Menu
•, ª,
0 , 1 : Cursor up, down,
left and right
ENTER : Enter
CHANNEL : Switch channels
+, –
0~9, +10 : Channels
TV/VCR : Switch between TV
and video player
TV VOL +, – : Volume up/down
DISPLAY : Switch display
RETURN : Return
NOTES:
• For this CD, CDR, MD and TAPE components, buttons can be operated in the same way as for Denon audio
components.
• The television can be operated in the DVD/VDP, VCR and TV modes.
If your AV component is not a DENON product or if it cannot be operated using the preset memory, it can be
controlled with the included remote control unit by storing its remote control signals in the remote control unit.
For some remote control signals it is not possible to “learn” the signals or the device will not operate properly.
In such cases use the remote control unit included with the device to operate it.
Learning function
1
Press the USE/LEARN button with the tip of a
pen etc., to set the learn mode.
• Both the mode selector buttons and
LEARNED/TX indicator flash.
2
Press the mode button of the equipment for
which learning is desired.
• Mode button and LEARNED/TX indicator
flash.
2
1, 3, 7
3
Press the button that is to be learned.
The LEARNED/TX indicator stops flashing and
the mode button lights.
• Mode button and LEARNED/TX indicator
flashed if a button that cannot be “learned” is
pressed.
•To cancel, press the USE/LEARN button.
4
5
Point the remote control units directly at each
other and press and hold
in the button on the
other remote control
unit which you want
to “learn”.
Other remote
control unit
6
To “learn” other buttons, repeat steps 2 to 5.
7
Once the learning operation is completed, press
the USE/LEARN button again.
The mode button and the LEARNED/TX
indicator stop flashing and the learning mode is
cancelled.
Flashes
The mode button and the LEARNED/TX
indicator lights, release the button
on the other remote control unit.
• The mode button and the
LEARNED/TX indicator start
flashing again.
Check that the stored
codes work properly.
NOTES:
• If the codes could not be stored, the
LEARNED/TX indicator start flashing rapidly. For
limited number of models, codes cannot be
stored in RC-924.
• If the mode button and LEARNED/TX indicator
start flashing rapidly, this means that the
memory is already full, and the code you have
just attempted to store was not stored.
To “learn” that code, first perform the resetting
operation. (See page 22.)

Denon AVR-2803 Specifications

General

Power Output	90 W per channel (8 ohms, 20 Hz - 20 kHz, 0.05% THD)
Channels	7.1
Dolby Support	Dolby Digital, Dolby Pro Logic II
Digital Inputs	2 coaxial, 3 optical
Weight	14.5 kg
Type	AV Receiver
Output Power per Channel	90 W (8 ohms, 20 Hz - 20 kHz, 0.05% THD)
Frequency Response	10 Hz - 100 kHz (+1, -3 dB)
Input Sensitivity	200 mV
Input Impedance	47 kOhms
Total Harmonic Distortion	0.05%
Input Sensitivity/Impedance	200 mV / 47 kOhms
Tuner Frequency Range	FM: 87.5 - 108 MHz, AM: 522 - 1611 kHz
DTS Support	DTS, DTS-ES, DTS Neo:6
Outputs	Composite: 2, Component: 1
Video outputs	Composite: 2