To Next PageTo Next PageWhat does “Overcurrent” mean on my Denon AVR-2311CI display?
If your Denon Stereo Receiver displays “Overcurrent”, it indicates that the USB memory device is using too much power. If using a USB portable hard disk, connect its AC adapter.
How to troubleshoot no sound from the subwoofer on a Denon AVR-2311CI Stereo Receiver?
If you're not getting any sound from your subwoofer with your Denon Stereo Receiver, here are some things to check: * Verify the subwoofer connections. * Make sure the subwoofer is powered on. * In the receiver's menu, ensure “Speaker Config.” – “Subwoofer” is set to “Yes.” * If “Front” and “Center” are set to “Large” and “SW Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode. Check the “Front” and “Center” settings.
Why is there no audio output with HDMI connection on my Denon AVR-2311CI?
If you're not getting audio through your HDMI connection on your Denon Stereo Receiver: * Check the HDMI connector connections to ensure they are properly connected. * To output audio from the speakers, set “HDMI Audio Out” to “AMP” in the menu. * To output audio from a TV, set “HDMI Audio Out” to “TV” in the menu.
How to improve radio reception on my Denon AVR-2311CI Stereo Receiver?
To improve radio reception and reduce noise or distortion on your Denon Stereo Receiver, try the following: * Adjust the antenna's orientation or location. * Keep the AM loop antenna separate from the unit. * Consider using an FM outdoor antenna. * Ensure the antenna is separated from other connection cables.
Why is there no sound from the surround back speaker of my Denon AVR-2311CI?
If you're not hearing sound from the surround back speaker on your Denon Stereo Receiver, try these steps: * Set “Amp Assign” on the menu to “Normal.” * Set “Speaker Config.” – “S.Back” on the menu to something other than “None.” * Set “Surround Parameter” – “S.Back” on the menu to something other than “OFF.” * Make sure the surround mode is not set to “STEREO.”
What does it mean when the power indicator on my Denon Stereo Receiver is blinking red after turning on?
If, after powering on, the power indicator on your Denon Stereo Receiver blinks red at 0.5-second intervals, the unit's amplifier circuit has likely failed. Turn off the power and contact a DENON service advisor.
How do I enable DTS sound output on my Denon AVR-2311CI Stereo Receiver?
To enable DTS sound output on your Denon Stereo Receiver, set “Decode Mode” on the menu to either “Auto” or “DTS.”
Why doesn't my Denon AVR-2311CI recognize my USB drive?
If your Denon Stereo Receiver isn't displaying “USB” on the menu when a USB memory device is connected: * Check the connection to ensure it's properly connected. * The USB device might not conform to the mass storage class; use a compatible device. * Ensure the USB device is not connected via a USB hub.
What to do if my Denon Stereo Receiver set does not operate properly?
If your Denon Stereo Receiver isn't operating correctly, try resetting the microprocessor.
Why is there no video output with HDMI connection on my Denon Stereo Receiver?
If you're experiencing no video output via HDMI on your Denon Stereo Receiver: * Check that the HDMI connectors are securely connected. * Ensure the input source matches the connected HDMI connector. * Verify that your TV is compatible with HDCP (High-bandwidth Digital Content Protection). Incompatibility can prevent proper video output.
General| Channels | 7.2 |
|---|---|
| HDMI Inputs | 6 |
| HDMI Outputs | 1 |
| Audio Formats Supported | Dolby TrueHD, DTS-HD Master Audio |
| Network Connectivity | Yes |
| Wi-Fi | No |
| Multi-Room Capability | Yes |
| Response Bandwidth | 10 Hz - 100 kHz |
| Signal-To-Noise Ratio | 100 dB |
| Input Impedance | 47 kOhms |
| Input Sensitivity | 200 mV |
| THD | 0.08 % |
| Audio D/A Converter | 192kHz/24-bit |
| HD Radio | Yes |
| HDMI Switching | Yes |
| Frequency Response | 10 Hz - 100 kHz |
| Total Harmonic Distortion | 0.08 % |
| Input Sensitivity/Impedance | 200 mV / 47 kOhms |
| Phono Input | Yes |
| USB Port | Yes |
| Bluetooth | No |
| Amplifier Output Details | 7 channels |
| Video Inputs | Composite video x 4 |
| Video Outputs | Composite video x 1 |
| Digital Audio Inputs | Optical x 2, Coaxial x 2 |
| Dimensions (W x H x D) | 434 x 151 x 380 mm |
Provides essential safety guidelines for operating the apparatus and precautions.
Details on 7-channel amplifier, HDMI 1.4 support, and HDMI connectivity.
Provides sequential steps for initial setup and playback.
Details the initial steps of Audyssey setup: preparation, detection, and measurement.
Covers calculation, check, store, and finalization of Audyssey setup.
Details the initial installation procedure for the unit.
Guides on connecting speakers, cables, and using banana plugs.
Instructions for connecting a Blu-ray Disc player and TV via HDMI.
Steps for powering on the unit, TV, and subwoofer.
Performing automatic speaker setup using Audyssey.
Guidelines for microphone placement and identifying the main listening position.
Adjusting subwoofer settings for optimal performance.
Initial preparation for the Audyssey auto setup process.
Automatic detection of connected speakers and their configuration.
Performing acoustic measurements at multiple listening positions.
Analysis of measurement data for speaker settings calculation.
Verifying measurement results and speaker configuration.
Saving the calculated speaker settings to memory.
Completing the Audyssey Auto Setup process.
Guides on selecting source, adjusting volume, muting, and setting listening modes.
Covers selecting input sources, adjusting volume, and muting audio.
Navigating the menu to select input sources.
Adjusting master volume and temporarily muting audio.
Covers HDMI features like 3D, ARC, Deep Color, cables, control, and 3D support.
Details on connecting various devices via HDMI.
Instructions for connecting a TV, including audio and video.
Steps and cable diagrams for connecting a DVD player.
Steps and cable diagrams for connecting a set-top box.
Steps and cable diagrams for connecting a digital video recorder.
Steps and cable diagrams for connecting a digital camcorder.
Instructions for connecting a DENON control dock for iPod.
Instructions for connecting iPod or USB devices directly to the unit's port.
Steps and cable diagrams for connecting a CD player.
Steps for playback, including preparation, power, source selection, and component setup.
Steps for CD playback: preparation, power, source selection, and component setup.
Methods for playing iPod content via control dock or USB.
Steps for connecting an iPod directly to the unit's USB port.
Details on iPod operation buttons and functions.
How to initiate iPod playback.
Information and steps for tuning into HD Radio stations.
Steps for manually tuning and storing favorite radio stations.
Selecting and listening to preset radio stations.
Installing and connecting speakers for non-5.1 channel setups.
Overview of speaker setup procedures: Install, Connect, Set Up.
Guides for speaker placement in 7.1ch, 6.1ch, and Front A/B setups.
Connecting front height speakers for 7.1 channel setup.
Connecting surround back speakers for 7.1/6.1 channel setup.
Connecting a single surround back speaker for 6.1 channel setup.
Connecting a second set of front speakers for A/B configurations.
Connecting speakers for 2.1 and 2-channel audio setups.
Connecting separate amplifiers to tweeters and woofers.
Connecting speakers for simultaneous 5.1 and 2.1 channel playback.
Setting the zone mode and operation mode on the remote control.
Connecting the setup microphone to the unit.
Configuring amplifier assignments for different speaker terminals.
Selecting speaker configuration (Normal, ZONE2, Height, Bi-Amp, Front B, 2CH).
Selecting channels to be used for speaker setup.
Selecting speaker channels (Front, Subwoofer, Surround Back).
Selecting front speakers (A, B, or A+B) for use.
Configuring subwoofer measurement or skip settings.
Configuring surround back speaker measurement or skip settings.
Switching input sources and controlling ZONE2 power.
Adjusting volume for ZONE2 and the main unit.
Temporarily muting audio output.
Setting MultEQ, Dynamic EQ, and Reference Level Offset.
Adjusting volume variations between content types.
