To Next PageTo Next PageWhy can't I play my iPod on my Denon AVR-2311CI?
If you're having trouble playing your iPod on your Denon Stereo Receiver, consider these points: * Check the iPod connections to ensure they are properly connected. * If using a control dock for your iPod, make sure its AC adapter is plugged into a power outlet. * Set the input source to “DOCK.” * Note that some incompatible iPod models might not play when connected via the USB port.
How do I turn on the display on my Denon Stereo Receiver?
If the display on your Denon Stereo Receiver is off, go to the menu and set “Dimmer” to a setting other than “OFF”.
Why is there no audio output from my Denon AVR-2311CI Stereo Receiver?
If you're not getting any sound from your Denon Stereo Receiver, here are a few things to check: * Make sure all your device connections are secure. * Verify the speaker connections are correct. * Ensure the connected audio device is powered on. * Adjust the master volume to an audible level. * Deactivate mute mode, if enabled. * Select the appropriate input source and mode. * Also, remember that when headphones are plugged in, no sound will come from the speakers or PRE OUT connectors, so disconnect the headphones.
What to do if my Denon Stereo Receiver set does not operate properly?
If your Denon Stereo Receiver isn't operating correctly, try resetting the microprocessor.
What does it mean when the power indicator is blinking red on my Denon AVR-2311CI Stereo Receiver?
If the power indicator on your Denon Stereo Receiver blinks red every 2 seconds, it means: * The unit's internal temperature has risen. Turn off the power and allow the unit to cool down before turning it back on. * Consider re-installing the unit in a location with better ventilation.
Why is there no video output with HDMI connection on my Denon Stereo Receiver?
If you're experiencing no video output via HDMI on your Denon Stereo Receiver: * Check that the HDMI connectors are securely connected. * Ensure the input source matches the connected HDMI connector. * Verify that your TV is compatible with HDCP (High-bandwidth Digital Content Protection). Incompatibility can prevent proper video output.
Why is the power indicator blinking red on my Denon Stereo Receiver?
If the power indicator on your Denon Stereo Receiver is blinking red at approximately 0.5-second intervals, this could indicate a couple of issues: * Ensure that you are using speakers with the correct impedance. * The speaker cable may have a short. To fix this, firmly twist the core wire in the speaker cable and reconnect it to the speaker terminal.
What to do if no picture appears on my Denon Stereo Receiver?
If you're not seeing a picture on your Denon Stereo Receiver, try these solutions: * Check the connection to your TV to ensure it is properly connected. * Make sure the TV input is set to the correct source.
Why is my Denon AVR-2311CI Stereo Receiver remote control not working?
If your remote isn't working with your Denon Stereo Receiver, consider the following: * Replace the batteries with new ones. * Make sure you're within 23 ft / 7 m of the unit and within a 30° angle. * Remove any obstructions between the remote and the receiver. * Ensure the batteries are inserted correctly, matching the polarity marks. * Avoid strong light exposure (like direct sunlight or certain fluorescent lights) on the receiver's remote control sensor.
How to fix a Denon AVR-2311CI Stereo Receiver that does not turn on?
If your Denon Stereo Receiver isn't powering on, try these steps: * Ensure the power plug is fully and correctly inserted into the power outlet. * If the protection circuit is active, disconnect the power plug from the outlet, wait 5 to 10 seconds, and then plug it back in.
General| Channels | 7.2 |
|---|---|
| HDMI Inputs | 6 |
| HDMI Outputs | 1 |
| Audio Formats Supported | Dolby TrueHD, DTS-HD Master Audio |
| Network Connectivity | Yes |
| Wi-Fi | No |
| Multi-Room Capability | Yes |
| Response Bandwidth | 10 Hz - 100 kHz |
| Signal-To-Noise Ratio | 100 dB |
| Input Impedance | 47 kOhms |
| Input Sensitivity | 200 mV |
| THD | 0.08 % |
| Audio D/A Converter | 192kHz/24-bit |
| HD Radio | Yes |
| HDMI Switching | Yes |
| Frequency Response | 10 Hz - 100 kHz |
| Total Harmonic Distortion | 0.08 % |
| Input Sensitivity/Impedance | 200 mV / 47 kOhms |
| Phono Input | Yes |
| USB Port | Yes |
| Bluetooth | No |
| Amplifier Output Details | 7 channels |
| Video Inputs | Composite video x 4 |
| Video Outputs | Composite video x 1 |
| Digital Audio Inputs | Optical x 2, Coaxial x 2 |
| Dimensions (W x H x D) | 434 x 151 x 380 mm |
Provides essential safety guidelines for operating the apparatus and precautions.
Details on 7-channel amplifier, HDMI 1.4 support, and HDMI connectivity.
Provides sequential steps for initial setup and playback.
Details the initial steps of Audyssey setup: preparation, detection, and measurement.
Covers calculation, check, store, and finalization of Audyssey setup.
Details the initial installation procedure for the unit.
Guides on connecting speakers, cables, and using banana plugs.
Instructions for connecting a Blu-ray Disc player and TV via HDMI.
Steps for powering on the unit, TV, and subwoofer.
Performing automatic speaker setup using Audyssey.
Guidelines for microphone placement and identifying the main listening position.
Adjusting subwoofer settings for optimal performance.
Initial preparation for the Audyssey auto setup process.
Automatic detection of connected speakers and their configuration.
Performing acoustic measurements at multiple listening positions.
Analysis of measurement data for speaker settings calculation.
Verifying measurement results and speaker configuration.
Saving the calculated speaker settings to memory.
Completing the Audyssey Auto Setup process.
Guides on selecting source, adjusting volume, muting, and setting listening modes.
Covers selecting input sources, adjusting volume, and muting audio.
Navigating the menu to select input sources.
Adjusting master volume and temporarily muting audio.
Covers HDMI features like 3D, ARC, Deep Color, cables, control, and 3D support.
Details on connecting various devices via HDMI.
Instructions for connecting a TV, including audio and video.
Steps and cable diagrams for connecting a DVD player.
Steps and cable diagrams for connecting a set-top box.
Steps and cable diagrams for connecting a digital video recorder.
Steps and cable diagrams for connecting a digital camcorder.
Instructions for connecting a DENON control dock for iPod.
Instructions for connecting iPod or USB devices directly to the unit's port.
Steps and cable diagrams for connecting a CD player.
Steps for playback, including preparation, power, source selection, and component setup.
Steps for CD playback: preparation, power, source selection, and component setup.
Methods for playing iPod content via control dock or USB.
Steps for connecting an iPod directly to the unit's USB port.
Details on iPod operation buttons and functions.
How to initiate iPod playback.
Information and steps for tuning into HD Radio stations.
Steps for manually tuning and storing favorite radio stations.
Selecting and listening to preset radio stations.
Installing and connecting speakers for non-5.1 channel setups.
Overview of speaker setup procedures: Install, Connect, Set Up.
Guides for speaker placement in 7.1ch, 6.1ch, and Front A/B setups.
Connecting front height speakers for 7.1 channel setup.
Connecting surround back speakers for 7.1/6.1 channel setup.
Connecting a single surround back speaker for 6.1 channel setup.
Connecting a second set of front speakers for A/B configurations.
Connecting speakers for 2.1 and 2-channel audio setups.
Connecting separate amplifiers to tweeters and woofers.
Connecting speakers for simultaneous 5.1 and 2.1 channel playback.
Setting the zone mode and operation mode on the remote control.
Connecting the setup microphone to the unit.
Configuring amplifier assignments for different speaker terminals.
Selecting speaker configuration (Normal, ZONE2, Height, Bi-Amp, Front B, 2CH).
Selecting channels to be used for speaker setup.
Selecting speaker channels (Front, Subwoofer, Surround Back).
Selecting front speakers (A, B, or A+B) for use.
Configuring subwoofer measurement or skip settings.
Configuring surround back speaker measurement or skip settings.
Switching input sources and controlling ZONE2 power.
Adjusting volume for ZONE2 and the main unit.
Temporarily muting audio output.
Setting MultEQ, Dynamic EQ, and Reference Level Offset.
Adjusting volume variations between content types.
