Denon AVR-2807 User Manual (English)

Other manuals for Denon AVR-2807

Service Manual130 pages

Specifications2 pages

Control Protocol22 pages

Questions and Answers:

V
valeriemcbrideSep 5, 2025
How to fix no image with HDMI connection on Denon AVR-2807 Stereo Receiver?
- P
  Pamela SchultzSep 6, 2025
  If you're not getting any image with an HDMI connection on your Denon Stereo Receiver, try these steps: * **Check HDMI Connection:** Ensure the HDMI output terminals of the receiver and the input terminals of the monitor are correctly connected. * **Select HDMI Input:** Properly select the HDMI signal input source. * **HDCP Support:** Verify that the connected monitor or equipment supports HDCP, as the receiver will not output video without it. * **Format Compatibility:** Confirm that the output format of the connected player (HDMI FORMAT) matches the supported input format of your monitor.
W
wduncanAug 25, 2025
Why is my Denon AVR-2807 display on but there is no sound?
- G
  Gabrielle WilliamsAug 25, 2025
  If the display is lit but no sound is coming from your Denon Stereo Receiver, here are a few things to check: * **Speaker Cables:** Make sure the speaker cables are securely connected. * **Function Knob:** Ensure the function knob is in the correct position. * **Volume Level:** Turn the volume up from the minimum level. * **Muting:** Switch off the muting function. * **Digital Signal Input:** Properly select a digital signal input source.
B
burnettgeorgeAug 25, 2025
Why is there no HDMI audio output from my Denon Stereo Receiver?
- S
  Seth AdamsAug 26, 2025
  If the HDMI audio is not being output on your Denon AVR-2807 Stereo Receiver, there are a couple of things to check: * **HDMI In Assign Setting:** If you want the receiver to play the audio, set the HDMI audio playback setting at the “HDMI In Assign” settings to “AMP.” * **HDMI In Assign Setting:** If you want the audio to come from the connected monitor device, set the HDMI audio playback setting at the “HDMI In Assign” settings to “TV.”
H
Holly KochAug 27, 2025
Why is sound only coming from the center speaker on my Denon AVR-2807?
- B
  Brandon FranklinAug 27, 2025
  If you're only hearing sound from the center speaker on your Denon Stereo Receiver, it might be because you are playing a monaural source (like TV or AM radio) in DOLBY/DTS SURROUND mode. To fix this, when playing monaural sources, select a surround mode other than DOLBY/DTS SURROUND mode.
B
billyjenningsAug 27, 2025
Why is there no DTS sound on my Denon AVR-2807?
- S
  Shannon HudsonAug 27, 2025
  If you're not getting any DTS sound from your Denon AVR-2807 Stereo Receiver, here are a few things to check: * **DVD Player Audio Output:** Ensure your DVD player’s audio output setting is set to bit stream. You may need to make the DVD player’s default settings. * **DVD Player Compatibility:** Confirm that your DVD player is DTS-compatible. If not, use a DTS-compatible player. * **Receiver Input Setting:** Check that the receiver’s input setting is set to “AUTO” or “DTS,” not analog.
G
Gary SantanaSep 13, 2025
What to do if my Denon AVR-2807 Stereo Receiver power has turned off and the power indicator is blinking red?
- A
  Ashley MartinezSep 13, 2025
  If the power indicator on your Denon AVR-2807 is blinking red and the power has turned off, it could be due to several reasons: * The internal temperature of the unit may have risen, activating the protection circuit. Ensure the AVR-2807 is placed in a well-ventilated area. * The core wires of the speaker cables might be touching each other or the AVR-2807’s rear panel, which also activates the protection circuit. Check all speaker cable connections. * The AVR-2807 may be malfunctioning. In this case, turn off the power.
S
Scott AtkinsSep 12, 2025
What does 'off air' mean on my Denon AVR-2807 Stereo Receiver in XM mode?
- E
  Edward MillsSep 12, 2025
  If “OFF AIR” is displayed in the XM mode on your Denon Stereo Receiver, it means the selected channel is not currently broadcasting. Select another channel.
T
Tamara FisherSep 12, 2025
Why is my Denon Stereo Receiver only receiving XM channels 0 and 1?
- G
  Gregory WilliamsSep 12, 2025
  If your Denon Stereo Receiver is only receiving XM channels 0 and 1, the XM Tuner is not activated. Contact XM Radio to activate it.
E
emily60Sep 4, 2025
What to do if the Denon AVR-2807 Stereo Receiver remote control is not working?
- P
  Patricia MyersSep 4, 2025
  If your Denon Stereo Receiver isn't working when using the remote, here's what to check: * **Batteries:** Replace dead batteries with new ones. * **Distance:** Move closer to the unit. * **Obstacles:** Remove anything blocking the remote's signal. * **Button:** Make sure you're pressing the correct button. * **Battery Insertion:** Ensure the batteries are inserted correctly, with the positive and negative ends properly aligned.
H
Heather CainSep 2, 2025
Why is there no sound coming from the surround speakers of my Denon Stereo Receiver?
- C
  Catherine LaneSep 2, 2025
  If you're not hearing sound from the surround speakers on your Denon Stereo Receiver, it might be because the surround mode is set to “STEREO”. Set to a mode other than “STEREO”.

Denon AVR-2807 Specifications

General

Number of Channels	7.1
HDMI Inputs	2
HDMI Outputs	1
Component Video Inputs	3
Component Video Outputs	1
Dolby Digital	Yes
DTS	Yes
Frequency Response	10 Hz - 100 kHz (+1, -3 dB)
Total Harmonic Distortion	0.05%
Input Sensitivity	200 mV
Signal-to-Noise Ratio	100 dB
Speaker Impedance	6-16 ohms
Tuner Type	AM/FM
Power Output	110W per channel
Digital Audio Inputs	2 coaxial
Auto Setup	Audyssey MultEQ
Multi-room	Yes
Width	434 mm
Height	171 mm
Dimensions	434 x 171 x 414 mm