How to fix no test tones on Denon Stereo Receiver?
If you're not getting any test tones from your Denon Stereo Receiver, it might be because the surround mode is set to a mode other than Dolby/DTS Surround. Set to Dolby/DTS Surround.
What to do if Denon AVR-2807 display is not lit and no sound is produced?
If your Denon Stereo Receiver display is not lit and no sound is produced when the power switch is on, the power supply cord may not be plugged in securely. Check the insertion of the power supply cord plug.
Why is there no DTS sound on my Denon AVR-2807?
If you're not getting any DTS sound from your Denon AVR-2807 Stereo Receiver, here are a few things to check: * **DVD Player Audio Output:** Ensure your DVD player’s audio output setting is set to bit stream. You may need to make the DVD player’s default settings. * **DVD Player Compatibility:** Confirm that your DVD player is DTS-compatible. If not, use a DTS-compatible player. * **Receiver Input Setting:** Check that the receiver’s input setting is set to “AUTO” or “DTS,” not analog.
Why is sound only coming from the center speaker on my Denon AVR-2807?
If you're only hearing sound from the center speaker on your Denon Stereo Receiver, it might be because you are playing a monaural source (like TV or AM radio) in DOLBY/DTS SURROUND mode. To fix this, when playing monaural sources, select a surround mode other than DOLBY/DTS SURROUND mode.
Why is there no HDMI audio output from my Denon Stereo Receiver?
If the HDMI audio is not being output on your Denon AVR-2807 Stereo Receiver, there are a couple of things to check: * **HDMI In Assign Setting:** If you want the receiver to play the audio, set the HDMI audio playback setting at the “HDMI In Assign” settings to “AMP.” * **HDMI In Assign Setting:** If you want the audio to come from the connected monitor device, set the HDMI audio playback setting at the “HDMI In Assign” settings to “TV.”
Why is my Denon AVR-2807 display on but there is no sound?
If the display is lit but no sound is coming from your Denon Stereo Receiver, here are a few things to check: * **Speaker Cables:** Make sure the speaker cables are securely connected. * **Function Knob:** Ensure the function knob is in the correct position. * **Volume Level:** Turn the volume up from the minimum level. * **Muting:** Switch off the muting function. * **Digital Signal Input:** Properly select a digital signal input source.
General| Number of Channels | 7.1 |
|---|---|
| HDMI Inputs | 2 |
| HDMI Outputs | 1 |
| Component Video Inputs | 3 |
| Component Video Outputs | 1 |
| Dolby Digital | Yes |
| DTS | Yes |
| Frequency Response | 10 Hz - 100 kHz (+1, -3 dB) |
| Total Harmonic Distortion | 0.05% |
| Input Sensitivity | 200 mV |
| Signal-to-Noise Ratio | 100 dB |
| Speaker Impedance | 6-16 ohms |
| Tuner Type | AM/FM |
| Power Output | 110W per channel |
| Digital Audio Inputs | 2 coaxial |
| Auto Setup | Audyssey MultEQ |
| Multi-room | Yes |
| Width | 434 mm |
| Height | 171 mm |
| Dimensions | 434 x 171 x 414 mm |
Step-by-step guide to configure the receiver for optimal sound and operation.
Details on how to connect various audio and video input devices to the receiver.
Explains how to select input sources, adjust volume, and use basic playback functions.
Covers advanced features like night mode, user memory, iPod control, and multi-zone operation.
Details on using the automatic system setup and room equalization for optimal acoustics.
Explains the initial measurement process to detect speakers and check polarities.
Guide to selecting and using various surround sound modes for different audio sources.
Overview of system setup categories and their default configurations.
How to assign digital input terminals and set levels for various audio sources.
Configuration for HDMI and component video assignments and conversion settings.
Manual configuration of speaker systems if auto setup was not performed.
Adjusts speaker volume levels to match output for a balanced sound experience.
To Next Page
