Denon AVR-3801 Operating Instructions

38
4
5
6
7
BAND MODE
TUNING
TUNING
ENTER
SHIFT
BAND MODE
TUNING
TUNING
ENTER
SHIFT
ENTER
SHIFT
Use the D and H cursor buttons to display “RESET PRE” on
the remote control unit, then press the ENTER button.
• After “SEL PRE” is displayed on the remote control unit’s
display, the registered preset memory is displayed on the
remote control unit’s display.
Use the D and H cursor buttons to
select the code to be reset.
When the mode you want to reset is shown on the remote
control unit’s display, press the ENTER button to reset the
preset memory.
“CONFIRM” is displayed. To reset the preset memory, press
the ENTER button while “CONFIRM” is displayed.
• “COMPLETE” appears on the remote control unit’s display.
(3) Resetting “learned” buttons
1
2
3
456
789
+10
0
TV/
VCR
OFF
TV
CD
CDR/MD/ TAPE RECEIVER
VCR DBS/CABLE
SKIP
SKIP
ENTER
MEMORY
VOLUME
CHANNEL
+
-
+
-
VDP DVD
POWER
REMOTE CONTROL UNIT
RC-883
ON /
SOURCE
TUNER
VDP
VCR-1 VCR-2/V.AUX
DVD
TV/DBS
CDR/TAPE
PHONO
CD
SURROUND
INPUT
OUTPUT
TEST
TONE
SPEAKER
6.1 / 7.1
SURROUND
5CH / 7CH
ANALOG EXT.INMODE
CALL 2 BACKLIGHT CALL 1
STEREO
STEREO
DOLBY/DTS
SURROUND
DSP
SIMU.
DISPLAY
SYSTEM CALL
DIRECT
RETURN
SETUP
MENU
SHIFT
SURR.
PARA.
OSD
A/B
MUTING
BAND MODE
TUNING
TUNING
1
3, 4, 5
2, 3, 4, 5, 6
1
2
3
ON /
SOURCE
OFF
ENTER
SHIFT
BAND MODE
TUNING
TUNING
ENTER
SHIFT
Press the power ON/SOURCE button and the OFF button at
the same time.
• “SET UP” appears on the remote control unit’s display.
Press the ENTER button.
Use the D and H cursor buttons to display “RESET” on the
remote control unit’s display, then press the ENTER button.
• “RESET PRE” is displayed.
4
BAND MODE
TUNING
TUNING
ENTER
SHIFT
Use the D and H cursor buttons to display “RESET LRN” on
the remote control unit’s display, then press the ENTER
button.
• “SEL MODE” is displayed, then “TV” appears.
5
BAND MODE
TUNING
TUNING
ENTER
SHIFT
Use the D and H cursor buttons to select the mode of the
button to be reset, then press the ENTER button.
6
ENTER
SHIFT
“CONFIRM” is displayed. To reset the “learned” button for
the selected mode, press the ENTER button while
“CONFIRM” is displayed.

Denon AVR-3801 Specifications

General

Channels	7.1
Power Output	105 W per channel (8 ohms, 20 Hz - 20 kHz, 0.05% THD)
Frequency Response	10 Hz - 100 kHz (+1, -3 dB)
Total Harmonic Distortion	0.05%
Type	AV Receiver
Input Sensitivity	200 mV (Line)
Input Impedance	47 kOhms (Line)
Output Voltage	1.2 V (Pre Out)
Video Switching	Composite, S-Video
Speaker Impedance	6 - 16 Ohms
Tuning range	FM, AM
Digital inputs/outputs	optical, coaxial
Signal-to-Noise Ratio	100 dB (Line)
Output Impedance	1.2k ohms