Denon DRA-275RD - Setup and Function Usage; Using Receiver Functions

SPEAKER CONNECTION ANTENNA INSTALLATION
Contim polarity (+. —) and ieft ana ght channels {L. Ri Connect tne speaker @ FM ANTENNA
pars to tha SPEAKER terminals A or B on the back panel. Connections must be The supplied indoor FM antenna can be usad inside wooden houses for re-
made with power cord disconnected ceiving locat FM stations and other strong FM signals. Suetch out the ends
of the antenna-and mount the sntenna on the walt of ceiling whets optimum
reception 1s achieved. A indoor FM antennas may not consistently ensure
Stable reception. due to envionment changes In such cases. the indoor FM
antenna should only be used temporarily until an outdoor FM antenna has
been instatied
When connecting an outdoor FM antenna, the use of 76 Q/ohms coanat
cable (3C-2V, §C-2Vtis suongly recommended
Preparing the cord
1 Pagel off tha sheatn
Note:
® Bo not connect two FM antennas simultsnsously.
2. Twrst the wres.
«© AMLOOP ANTENNA
Tune in an AM station, listen to the sound, then instal! the antanna ma position.
as far from tha set as possible in which distortion and noise are minimum.
Good reception of AM stations 1s not possible if tha loop antenna ss not con-
nected or if it 1s touching metat objects
Connecting the tront speaker terminals
1 Loasen by turning counterciocawise
\D)
2. insert the cord and tighten by turning clockwise.
a
Connecting banana plugs
—
Turn clockwise to lighten, then insert the banana plug
Banana plug
* Speaker impedance
© When speaker systems A and B are use separately, speakers with an im-
pedance af fram 6 to 16 Q/ohms can be connected.
© Be careful whan using two pars of speakers {A + B) at the same time,
since use of speakers with an impedance outside the range of 12 to 16
Qrohms wil lead to damage.
@ = The protection circuit May Operate or damage may occur when speakers
with an impedance outside of the above range are used.
10
USING THE VARIOUS FUNCTIONS
1. Presetting stations in the memory
The frequency and the name of the radio station {including names which you
have input yourself}, are siso stored in the memory.
In parvcular, the various ADS functions can be used aftectivaly when ROS sts-
bons are stored in the memory.
How to preset the memory.
Press the MEMORY button (} . The “MEMO CH” inaicator on the display
flashes. Next, use SHIFT/PTY button @) to select the memory block A. B.
C. Dor E. Now press the TUNING PRESET UP or DOWN button @ to specily
The preset channe! number, and then press the MEMORY button @ to store
the station in the memory.
The preset channel numbers for the different memory blocks are as follows
Memory block A 108
Memory block 8 hos
Memory biock C 108
Memory diock 0 108
Memary biock E 108
The DRA-275R does not have a SHIFT /PTY bution Use the SHIFT button)
instead
Auto Memory (FM only!
Tne ORA-375RD/ORA-275A 15 equipped with an auto memory function.
Connect the antenna, set i! so that stations can be received. then hold wn the
MEMORY buiton ang press Ine POWER button to turn the power on Stations.
for which the auto tuning tunction operales are stored in the preset memory
1n the order Al to AB. B1 to BB. and so on. through EB.
Channel Al 1s tuned in after the auto Memory operation s completed
Using this function makes st possible to find out the overall reception cond.
trons of the receivable stanons The memory can be used effectively by tecal-
ling the channels in the preset memory and replacing stations whose recep:
lon 1s Poor with stations whose reception i$ good. using tne procedure
descnbed in 1 above.
Recalling preset stations
Use the SHIFT/PTY button @ to select memory piock A. B.C. O or €, then
press the TUNING PRESET UP or DOWN button QD to recall tne station
$10r8d in the memory.
It the TUNING PRESET UP or DOWN buttons are pressed without pressing
the SHIFT/PTY button @). tne stations are recalled in the order Al to AB, B1
to B8, ana so on, through EB
The DRA-275R does not nave a SHIFT/PTY buiton Use the SHIFT button
® nstead
RDS search (for FM only! (DRA-375RD only)
Use this function to automatically tune to stations offering Radio Data Service.
This operation 1s also possible by pressing the TUNER button on the remote
Control unit once when the function 1s set to the TUNER mode.
Operation Orsptay
1. Press the ROS button ROS SEARCH
once. 4
2. Press tha TUNING PRESET UP “RDS SEARCH" flasnes on the
of DOWN button display.
(Prasat memory channels Al
to EB are being searched.)
If no RDS station is found with tne
above operation. alt the reception
bangs are searched.
Tha station name 1s displayed,
when the RDS station is tuned.
3. Press the TUNER UP or RDS searcn starts again
DOWN button @ again while
the RDS mark is flashing
{it no other RDS station is found when aii the frequencies are searched, “NO
RDS* is displayed)
5. PTY search (for FM only) IDRA-375AD only)
Use this tunction to find stations broadcasting a designated type of pio.
gramme type (PTY)
This operation :s also possible by pressing the TUNER burton on the remote
CONTrOl uml twice when the function is set fo the TUNER mode. Next, press
the PANEL button on tne remote control uni, selact the PTY category. hen.
press the TUNING PRESET UP or DOWN buttons to start ihe PTY search func-
tron in the specified direction.
Operation
1 Press the ROS button
twice.
Display
PTY SEARCH
4
2 Press the SHIFT/PTY button Programme type or PTY.
Designated programme type
(Atways do this 10 designate the programme type if “PTY* is displayedin siep
tt
3. Prass the TUNING PRESET UP “PTY SEARCH” liashes on the
or DOWN button) display.
(Preset memory channels Al to EB
are being searched }
Wf there 1s no station broadcasting
the designated programme type
with the above operation, ail the re:
ception bands are searched
The station name is displayed alte:
searching siops
4 Press the TUNING PRESET uP PTY search starts again
or OOWN button again while
the PTY mark 13 flashing
Uf no other station broadcasting the designated Programme type 1s found
when
ail
he
frequencies
are
searched,
“NO
PROGRAMME"
is
displayed.)
The programme types which can be displayed are listed on page 12
6. TP search (for FM only) (ORA-375RD only)
This
tuncuion
13
used
to
find
stations
scheduled
to
broadcast
trallic
pro:
grammes ITP stations}.
This
operation
+s
aso
possible
by
pressing
the
TUNER
button
on
the
remore
Control unt three times when the funclion 1s set to the TUNER mode.
Operation Orspiay
1. Press the AOS button & TP SEARCH
Jtimes. t
2. Press the TUNING PRESET UP. “TP SEARCH™ flashes on the dis.
or DOWN button ® play.
(Preset memory channels Al
to E68 are being searched }
Hf 0 TP station 1s found with the
above operation, all the reception
bands are searched.
The station name ts displayed alter
searching stops
3 Press the TUNING PRESET UP TP search starts again
or DOWN button again while
the TP mark is Hashing
lit no ether TP station is found when all the frequencies are searched, “NO.
PROGRAMME" 5 displayed.)
7. RT (Radio Text) (for FM onty) (DRA~375RD only)
When the AT button @ ts pressed while the stanion currently tuned inis otter:
INg 8 radio text Message service, the message scrolls on the display.
(The RT indicator hghts when the RT button is pressed }
RABTO TEXT
rex? penearcas
1°NO
TEXT
DATA"
ts
dispiayed
it
no
radio
teat
Message
1s
being
broadcast
}
11
Se I a TT TEASE 8920/O0uS2Zc7/OY8SZE-ve"d ee