Denon DRA-335R - Back Panel Connections

ENGLISH
BACK PANEL
DRA-435R only
DENON move wo DRA-435R
POWER SURCE 220V -SOHz
POWER CONSUMPTION
ALIMENTATION
CONSOMMATION.
w
220v Son
a
NO.
NIPPON COLUMBIA CO.LTD
AB
PRE OUT
WARNING stock HAZARD DO NOT OPEN CAUTION
AVIS RISQUE DE CHOC FLECTRIQUE amare] /[) 0
: Tonat one i
SPEAKER IMPLDANCE
Ace
& 16Ohms/ SPEAKER
12 160hms/ SPEAKER
) L
al REMOTE
@
NE PaS OUVRIR
SPEAKER SYSTEMS ~~)
OQ AC OQUILET
Qr®
Ac
TAPE
CONTROL
WARNING TO REOPICE THE RISK OF FIRE
DRA-435R only
1)
FM
ANT
(FM
antenna
terminals)
9)
Both
75-ohm
coaxial
cable
and
300-ohm
feeder
can
be
connected
to
this
terminal.
For
antenna
connecting
proce-
dure,
see
the
ANTENNA
INSTALLATION.
Qa AM ANT (AM antenna terminals)
Connect the attached AM loop antenna. (Refer to page 7 for
connections).
Connect to this terminal when a medium wave outdoor
antenna is used.
3] GND (Grounding terminal)
The grounding wire of the turntable is connected here.
e Hum or noise may be generated if the grounding wire is @
not connected.
4] PHONO (Phono input terminals)
The
output
cord
of
the
turntable
is
connected
here.
®@
Since the input sensitivity of “PHONO” is extremely high,
do
not
use
the
unit
without
the
input
pin
cord.
If
used
without this cord, the speakers may generate hum.
©
co
®
The output cord of the CD player is connected here.
@ vive ®
A
VIDEO,
such
as
a
VCR
or
Video
Disk
may
be
connected
here.
(7) e TAPE-1, TAPE-2/VCR (Tape deck and/or VCR
playback/recording terminal) (DRA-435R)
Two tape decks or tape deck and VCR can be connected
to these jacks for full-fledged playback, recording and
tape
dubbing
operation.
®
¢ TAPE (DRA-335R)
Tape decks can be connected for full use including
playing or copying.
@®
_
pRE-OUT
(DRA-435R
only)
Output
signals
for
power
amplifiers
are
sent
from
these
jacks.
The
rated
output
is
1.0
volts.
The
signals
do
not
pass
through
the
bass
and
treble
circuits.
OR ELECTRIC SHOCK, PO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
9) ©
TAPE/REMOTE CONTROL
This
terminal
is
exclusively
used
for
sending
the
remote
control
signals
to
the
tape
deck.
Connect
it
with
a
3.5mm
mini-jack
cord.
Note:
Do not hook up a headphones or microphone jack
cord. Use this jack to connect a Denon cassette deck
with a remote control jack (wired).
If the cassette deck does not have this jack, wired
remote control is not possible.
SPEAKER SYSTEMS (Speaker terminals)
Two
pairs
of
speakers
A
and
B
can
be
connected
to
these
terminals.
AC OUTLET (AC power outlet) (Europe model only)
This AC outlet is controlled by the power switch Maximum
capacity is 100 W. (DRA-435R: This AC outlet is controlled
by the remote contro! unit.)
AC CORD (Power cord)
Connect this cord into the wall outlet.
VIDEO (Video input/output terminals) (DRA-435R
only)
As a full-featured AV center, this receiver makes possible
connection of a TV monitor, VCR and/or a videoctisc player
(Video) to these jacks. Use the Video INPUT SELECTOR
buttons on the front panel to select the desired source for
playback, recording or dubbing.
AM LOOP ANT (AM loop antenna)
Correctly connect the AM loop antenna to the antenna
terminal. Broadcasting cannot be received when the con-
nection is incomplete.
Adjust
the
antenna
for
optimum
reception
whie
receiving
-
the medium wave broadcasting. Do not place a»i n cord, SP
cord or electric cord near the antenna. This may cause
noise generation.