To Next PageTo Next PageWhy is my Denon Stereo Receiver display lit but there is no sound?
If your Denon Stereo Receiver's display is lit but there's no sound, there might be a few reasons: * Check if the speaker cables are securely connected. * Ensure the INPUT SELECTOR knob is in the correct position. * Verify the volume isn't set to minimum; turn it up. * Make sure MUTING is switched off.
What to do if my Denon DRA-500AE Stereo Receiver remote control is not working?
If your Denon Stereo Receiver isn't responding to the remote control, try these steps: 1. Replace the batteries with new ones. 2. Move closer to the unit. 3. Ensure there are no obstacles between the remote and the receiver. 4. Make sure you're pressing the correct button. 5. Check that the batteries are inserted with the correct polarity (+ and - ends).
Why is the power indicator blinking red on my Denon DRA-500AE Stereo Receiver?
If the power on your Denon Stereo Receiver has turned off and the power indicator is blinking red, it could indicate a problem. Here's what might be happening: * The unit's internal temperature may have risen, activating the protection circuit. Ensure the receiver is in a well-ventilated area. * The speaker cables' core wires might be touching each other or the receiver's rear panel, triggering the protection circuit. Inspect all speaker cable connections. * If neither of these resolves the issue, the receiver may be malfunctioning. In this case, turn off the power.
General| Impedance | 8 Ω |
|---|---|
| Receiver type | stereo |
| Frequency range | 20 - 20000 Hz |
| Maximum input power | 75 W |
| Audio output channels | - channels |
| Total Harmonic Distortion (THD) | 0.05 % |
| Power output per channel (20-20KHz@8 Ohm) | 95 W |
| AirPlay | No |
| Display | - |
| Equalizer | Yes |
| Product color | Black |
| Apple docking compatibility | Not supported |
| RDS features | EON |
| AM band range | 522 - 1611 kHz |
| FM band range | 87.5 - 108 MHz |
| Supported radio bands | FM, MW |
| Preset stations quantity | 56 |
| Connectivity technology | Wired |
| HDMI in | 0 |
| Audio (L/R) in | 5 |
| Audio (L/R) out | 2 |
| Headphone outputs | 1 |
| Headphone connectivity | 6.3 mm |
Weight and Dimensions| Depth | 414 mm |
|---|---|
| Width | 434 mm |
| Height | 147 mm |
| Weight | 9000 g |
Identifies the specific models covered by this service manual.
Crucial safety instructions and warnings for servicing and handling the unit.
Procedure to check for leakage current before returning the unit to the customer.
General warnings and precautions for safe handling, assembly, and part replacement during servicing.
Ensures safety checks are performed after completing service tasks.
Emphasizes correct handling and replacement of critical safety components.
Detailed steps to adjust the unit's idling current for optimal performance.
Steps for preparing the unit and setting initial parameters before adjustment.
Details and pin configurations for integrated circuits.
Illustrates the internal functional blocks of the NJW1197 integrated circuit.
Functional block diagram of the BA7626F video switch IC.
Shows the component placement and routing on the main P.W.B.
Component layout for the front P.W.B. of DRA-700AE/700AEDAB models.
Component layout for the front P.W.B. of the DRA-500AE model.
Comprehensive list of resistors and capacitors with part details.
Lists Zener diodes, resistors, and capacitors with their specifications.
Lists parts for major unit assemblies like main, front, input, audio, and control boards.
Illustrates the internal wiring and interconnections between major boards for specific models.
Critical safety warnings and procedures for servicing and handling the unit.
Schematics for the main amplifier and power switch boards.
Schematics for the front, zone, and headphone boards.
