Denon DRA-565RD - Tuning and Memory Operations; Station Presetting and Recall; Advanced FM Tuning Features

Preset (Preset station buttons)
These buttons are used for storing stations or recalling
stations which have been preset. Using the SHIFT button
you can preset a total of 40 FM or AM stations into preset
channels.
Once a radio has been memorized, the same station can
later be tuned in instantly simply by recalling the corres-
ponding preset channel with PRESET UP or DOWN button.
DISPLAY
© €@e8 8® 88 6
RDS indicator
This lights when receiving RDS broadcasts, and flashes
during the RDS search operations.
TA indicator
This lights when receiving traffic announcements.
TP indicator
This flashes during the TP search operation and lights
when TP stations are tuned in.
PTY indicator
This flashes during the PTY (Programme type) search
operation.
TUNED indicator
This lights when a station is property tuned in.
STEREO indicator
This lights when receiving stereo broadcasts. It remains off
when receiving AM broadcasts.
AUTO indicator
This indicates the tuning mode. It lights in the auto mode,
and remains off in the manual mode.
NOTE:
e TP (Traffic Programme)
Stations scheduled to broadcast traffic programmes
e TA (Traffic Announcement)
Traffic information broadcasts
REAR PANEL
(2)
FM ANT (FM antenna terminals)
75-ohm coaxial cable can be connected to this terminal. For
antenna connecting procedure, see the ANTENNA IN-
STALLATION.
GND (Grounding terminal)
The grounding wire of the turntable is connected here.
e¢ Hum or noise may be generated if the grounding wire is
not connected.
AM ANT (AM antenna terminals)
Connect the attached AM loop antenna. (Refer to page 10
for connections).
Connect to this terminal when a medium wave outdoor
antenna is used.
PHONO (Phono input terminals)
The output cord of the turntable is connected here.
Since the input sensitivity of “PHONO” is extremely high,
do not use the unit without the input pin cord. If used
without this cord, the speakers may generate hum.
cD
The output cord of the CD player is connected here.
VIDEO
A VIDEO, such as a VCR or Video Disc may be connected
here.
e TAPE-1, TAPE-2 (Tape deck playback/recording
terminal) (DRA-565RD)
Two tape decks or tape deck can be connected to these
jacks for full-fledged playback, recording and tape
dubbing operation.
e TAPE (DRA-365RD)
Tape decks can be connected for full use including
playing or copying.
®
e e 6 9
ENGLISH
e SHIFT/PTY button
Use
this
button
to
select
the
memory
blocks,
A
(1 to
8),
B
(1
to
8),
C
(1
to
8),
D
(1
to
8)
or
E
(1
to
8).
For
PTY
search,
use
this
button
to
select
the
program
type.
When
writing
station
names,
use
this
button
to
set
the
writing
position.
MEMO indicator
This
indicator
lights
for
approximately
10
seconds
when
the
MEMORY
button
has
been
pressed
and
a
station
can
be
stored
on
a
PRESET
CHANNEL
button.
This
flashes
continuously
during
the
auto
memory
opera-
tion.
CH indicator ;
This
lights
when
the
preset
channel
number
and
shift
mode
(A, B, C, D or E) are displayed.
© TAPE-1/TAPE-2 indicator (DRA-565RD)
The
TAPE-1
indicator
lights
when
the
TAPE-1
source
is
selected
with
the
tape
selector
buttons.
The
TAPE-2
indicator
lights
when
the
TAPE-2
source
is
selected.
e TAPE indicator (DRA-365RD)
The
TAPE
indicator
lights
when
the
TAPE
source
is
selected with the tape selector buttons.
Multi function display
This
displays
the
frequency,
station
name,
programme
type, etc.
PRE-OUT (DRA-565RD only)
Output
signals
for
power
amplifiers
are
sent
from
these
jacks.
The rated output is 2 volts.
SPEAKER SYSTEMS (Speaker terminals)
Two pairs of speakers A and B can be connected to these
terminals.
AC OUTLET (AC power outlets)
This
AC
outlet
is
controlled
by
the
power
switch
and
Remoto
controlunit
(DRA-565RD),
controlled
by
the
power
switch
(DRA-365RD).
AC CORD (Power cord)
Connect this cord into the wall outlet.