DeWalt DCV586 - Troubleshooting; Motor Issues; Dust Extraction Problems; Wireless Tool Control Issues

15
ENGLISH
hazardous area and appropriate measures must be taken
to avoid dustdistribution.

WARNING: To reduce the risk of serious personal
injury, turn dust extractor off and disconnect battery
pack before making any adjustments or removing/
installing attachments or accessories and if the
dust extractor head is removed from the tank or not
latched securely. An accidental start‑up can causeinjury.
The dust extractor must be handled for cleaning and
maintenance in a way, that avoids exposing maintenance
personnel and other persons to anyhazards.
• Wear personal protectiveequipment.
• Use filtered forcedventilation.
• Clean the dust extractor. Refer toCleaning.
• When maintenance or repairs are carried out, all
contaminated parts which cannot be satisfactorily cleaned
must be packed in impermeable bags and disposed of in
compliance with the applicable disposalregulations.
• After maintenance or repairs clean the maintenance area in
a way that prevents hazardous substances escaping into the
surroundingenvironment.
The charger and battery pack are notserviceable.
Lubrication
Your dust extractor requires no additionallubrication.
Cleaning (Fig. A, I)

WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the dust extractor.
These chemicals may weaken the materials used in these
parts. Use a cloth dampened only with water and mild
soap. Never let any liquid get inside the dust extractor;
never immerse any part of the dust extractor into aliquid.
For cleaning and maintenance in a way that avoids exposing
maintenance personnel and other persons to any hazards, wear
personal protective equipment. Clean the maintenance area in a
way that prevents hazardous substances from escaping into the
surroundingenvironment.
Do not use a spray system, pressure jet washer or running water
forcleaning.
1. Vacuum the outside of the dust extractor. For further
cleaning use a cloth dampened only with water and mild
soap ifnecessary.
2. After use dispose of cloth in an appropriatecontainer.
3. Empty tank according the the section Dust
ExtractorCleaning.
4. Inspect water sensor probes
25
during dust extractor
cleaning. Water sense probes may become contaminated
during operation. If contamination is present, clean water
sense probes thoroughly with damp cloth to remove any
visiblecontamination.
Storage (Fig. A)

CAUTION: The three position switch must be in OFF (0)
position to prevent unintentional being switched on by
Wireless ToolControl.
1. Empty the tank. Refer to Dust Extractor Cleaning
underOperation.
2. Clean the dust extractor inside andoutside.
3. Clean or replace filters, refer toFilters.
4. Store the suction hose with the hose clips
5
and the power
cord as shown in the illustration. Place the unit in a dry room
and secure it from unauthorizeduse.
NOTE: Plug hose inlet plug
9
into inlet to keep debris inside
canister when suction hose is removed. You can also attach
the ends of the hose together and lock together with the
twist‑lockend.
Optional Accessories

WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product,
use of such accessories with this dust extractor could
be hazardous. To reduce the risk of injury, only DeWALT
recommended accessories should be used with
thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
A replacement filter is available at extra cost at your local
DeWALT servicecentre.
Dust Collector
In the vacuum mode, the appliance can also function as a dust
collector for power tool applications producing dust ordebris.
IMPORTANT! The DWV9000 dust extraction adaptor is
designed to work with Dust System Compatible DeWALT
power tools. An additional adaptor will be needed with
non‑compatible DeWALTtools.
Optional Accessories
• DCV5861 Replacement Filters (Contains 2DC5151H filters)
• DWV9316 Anti‑Static Hose
• DWV9350 Floor Cleaning Kit
• DWV9000 Twist Lock connection
• DWV9110 29mm–35mm tapered rubber adaptor
• DWV9120 35mm–38mm stepped rubber adaptor
• DWV9130 35mm OD Adaptor
• DWV9150 35mm OD angle adaptor
• DWV9210 Construction Kit (DWV9000 + DWV9120 +
DWV9130)
• DWV9220 Woodworking Kit (DWV9000 + DWV9130 x 3 +
DWV9120 + DWV9150 + Cable Hose Clip)
• DWV9470 Y Splitter Hose Kit
• DWST17889 Cart
• DWST17888 Trolley
The filter bags provide a clean, easy and quick way to dispose of
the dustcollected.