DeWalt DCV586 - Rechargeable Battery Pack Care

14
ENGLISH
Dust Extractor Cleaning
To Empty Tank (Fig.A, F, H,I)

WARNING: Appropriate personal protective equipment
like a dusk mask and gloves should be used while cleaning
the dust extractor and emptying thetank.

WARNING: Emptying and maintenance, including
disposal of the dust collection container, may be carried
out only by trained and qualified specialists. Wear the
appropriate protectiveequipment.
The buzzer sounds and suction is reduced when the tank isfull.
1. Press the three position switch
3
to the Off (O) position and
remove thebattery
7
.
2. Close the twist‑lock hose inlet with the hose inlet plug
9
.
3. Remove the dust extractor head
6
from thetank
21
.
4. Dispose of collection bag in appropriate container according
to statutoryprovisions.
5. Clean or change filters
17
. Refer to Filter section of
thismanual.
6. Inspect machine for damage by foreign objects. Contact the
nearest DeWALT authorized service centre for replacement
of damaged or missingparts.
7. Replace dust extractor head onto the tank and
latchsecurely.
Stacking Using the DeWALT TSTAK Stacking
Latches (Fig. A)

WARNING: When stacking, always place the dust
extractor on thebottom.
The DEWALT TSTAK stacking latches
10
l allow for other
TSTAK products to securely stack one on top of the other for
convenience andportability.
To use the TSTAK stacking latches
10
, place a TSTAK compatible
unit on top of the dust extractor and flip up the two TSTAK
stacking latches so that they clip securely to the bottom of
theunit.
Filters

WARNING: The filters must always be in place
whilevacuuming.
Filter Care
The filters included with this dust extractor are long life filters. To
be effective in minimizing dust recirculation, the filters MUST be
installed correctly and in goodcondition.
Automatic Filter Cleaning System
This dust extractor has a highly effective filter cleaning system
which minimizes filter clogging. Every 20seconds, one of the
two filters gets automatically cleaned. The cleaning process
alternates between the filters and continues through the life of
theunit.
NOTE: It is normal to hear a clicking sound during thisprocess.
NOTE: After many hours of operation the automatic filter
cleaning system may not be effective. When this happens the
filters will need to be cleaned or replaced.
To Remove Filters (Fig. A, H, I)

WARNING: Appropriate personal protective equipment
like dust mask and gloves should be used while handling
thefilters.
1. Press the three position switch
3
to the Off (O) position and
remove thebattery
7
.
2. Release tank latches
4
and remove dust extractor head
6
from canister. Place dust extractor head on a level surface
upsidedown.
3. Turn each filter
17
counterclockwise, and carefully remove
from dust extractor head, ensuring debris does not fall into
mountinghole.
NOTE: Use care to not damage filtermaterial.
4. Inspect filters for wear, tears or otherdamage.
NOTE: If there is any doubt on the condition of the filters,
they MUST be replaced. DO NOT continue use if filters
aredamaged.

WARNING: Never use compressed air or a brush to clean
filters, otherwise damage to the filter membrane will
occur which will allow dust to pass through the filter.
If needed, rinse with room temperature water and let
air dry. Cleaning of the filters is typically unnecessary.
Even if the filter is covered with dust, the automatic filter
cleaning system will maintain maximum performance
and continue to function. If visual damage to the filter
membrane exists, replace filters. Filters typically last
between six and twelve months, depending on use
andcare.
NOTE: Dispose of filter in appropriate container according to
statutoryprovisions.
To Install Filters (Fig.E, F, I)

WARNING: The filters must always be in place
whilevacuuming.
1. Ensure filter seal
24
is in place and isclean andsecure.
2. Line up the tabs on the filter
17
to the notches on the dust
extractor head and using moderate force, turn clockwise
until the filter issecure.
NOTE: Use care to not damage filtermaterial.
3. Place the dust extractor head
6
onto the tank
21
and
secure it by closing the tank latches
4
.
MAINTENANCE
The appliance must be subjected to a technical inspection
by DeWALT Service or a trained person at least once a year to
check, damage to the filter, air leakage, and to ensure correct
operation of controllingdevices.
NOTE: Cleaning and user maintenance shall not be made by
children.

WARNING: For vacuum cleaners of the class M, please
note: The exterior of the dust extractor should be
decontaminated by dust extraction and wiped clean
or seal it in a suitable container or material before
being removed from an area contaminated with
hazardous substances; All parts of the dust extractor
must be considered contaminated when taken out of the