DH Instruments PPC3 - Commands; Programming Messages; Table 16. Program Message List

4. REMOTE OPERATION
Page 85 © 2002-2007 DH Instruments, a Fluke Company
4.4 COMMANDS
4.4.1 PROGRAMMING MESSAGES
Table 16. Program Message List
#
Send a command string out of the PPC3 COM2 port.
ABORT
Stop pressure generation.
ARANGE
Read or set a new AutoRange to use.
ATM
Read the current atmospheric pressure (on-board barometer).
AUTOPURGE
Read or set the status of the automatic purge function.
AUTOVAC
Read or set the status of the control reference (EXHAUST port).
AUTOZERO
Read or set the status of the AutoZ automatic zeroing function.
CALAMB
Read or set the on-board barometer calibration
COM1
Read or set the configuration of the COM1 port.
COM2
Read or set the configuration of the COM2 port.
DATE
Read or set the current date.
DF
Decrease the pressure quickly (fast).
DP
Decrease the pressure a given amount.
DRV
Read or set the status of the external valve drivers.
DS
Decrease pressure slowly.
ERR
Read the last error message.
GPIB
Read or set the GPIB interface address.
HEAD
Read or set the fluid head settings.
HS
Read or set the current control hold limit in pressure.
HS%
Read or set the current control hold limit in percent span of the active range.
ID
Read or set the PPC3 alphanumeric asset ID tag.
IF
Increase the pressure quickly (fast).
IP
Slowly increase the pressure a given amount.
IS
Increase the pressure slowly.
L2
Selects “classic” program message format
L3
Selects “enhanced” program message format
LL
Read or set the lower limit for the current range (negative gauge mode only).
LOCAL
Return control to the PPC3 front panel.
MEM
Read the power-up memory test status.
MMODE
Read or change the active measurement mode.
MODE
Read or set the current pressure control mode.
MSGFMT
Read or set the type of program message format to use.
NVENT
Read or set the status of the lo vent valve (Gxxx or BGxxx Q-RPT only).
PASSTHRU
Send a command string out of the PPC3 COM2 port.
PCAL:IH
Read or set the user Lo RPT calibration information.
PCAL:IL
Read or set the user Hi RPT calibration information.
PCALn:HI
Read or set the user Hi RPT calibration information (PPC2+ legacy command).
PCALn:LO
Read or set the user Lo RPT calibration information (PPC2+ legacy command).
PR
Read the next PPC3 pressure.
PRR
Read the next PPC3 pressure, rate, and ATM.
PS
Set a new target pressure and start automated pressure control.
PSF
Set a new target pressure and use only the fast speed to reach the target.
PSS
Set a new target pressure and use only the slow speed to reach the target.
QPRR
Read the last PPC3 pressure, rate and ATM.
RANGE
Read or set the active range (PPC2+ legacy command).
RANGE
Read or set and Q-RPT or utility sensor default range (PPC3 command).
RATE
Read the next available rate of change of pressure.
READYCK
Read or set a flag that is cleared by a Not Ready condition.
REMOTE
Enable remote local lockout operation.
RES
Read or set the pressure display resolution for the current transducer and range.
RESET
Reset the PPC3 to the default user parameters.
RETURN
Start a new automated pressure control set using the current target value.
RPT
Read the available Q-RPT data or initiate the RPT search process.
SCRSAV
Read or set the front panel screen saver period.
SN
Read the serial number of the PPC3.
SR
Read the next available pressure status (Ready/Not Ready).
SS
Read or set the stability required for a Ready condition.
SS%
Read or set the stability required for a Ready condition (% span/ s).
STAT
Read the pressure generation status.