Why PG7601 motorized rotation will not engage in DH Instruments ADCS-601?
If the PG7601 motorized rotation will not engage on your DH Instruments Test Equipment, the motorized rotation system may be recovering from an overload, or the measurement made is absolute by vacuum and the reference vacuum is not under the Ready limit. Wait 25 seconds for the system to recover.
What to do if ADCS component displays or in DH Instruments ADCS-601?
If the ADCS component of your DH Instruments Test Equipment displays or where a numerical value should be, it means the number to be displayed is too large for the allocated space. This is usually due to an erroneous setting or measurement causing an out of limit high value to be calculated. Check the settings that may be causing an out of limit high measurement and adjust if necessary.
Why is automated pressure generation extremely slow in DH Instruments ADCS-601 Test Equipment?
If automated pressure generation in your DH Instruments Test Equipment is extremely slow or the pistons never float, the test volume might be too large. Try reducing the test volume.
What does it mean when PG7601 displays or in DH Instruments ADCS-601 Test Equipment?
If the PG7601 displays or in DH Instruments Test Equipment, this indicates a communications problem with an external device or pressure generation/control component. Check the setup and communications with the external vacuum gauge or pressure generation/control component.
How to fix vacuum pumps that will not run on DH Instruments ADCS-601 Test Equipment?
If the system’s vacuum pump(s) of your DH Instruments Test Equipment will not run, the fuse on the AC2 or AC3 power supply connection may have blown. Replace the fuse on the AC2 or AC3 IEC power connector on the rear of the Control Cabinet. The fuse should be a 250 VT 10 A.
What does mean in DH Instruments Test Equipment?
If ADCS Tools displays for your DH Instruments Test Equipment, the FPG8601 is in a condition in which it cannot be used. View the FPG8601 Run Screen in ADCS Tools and check for noisy output or other abnormal conditions.
Why is FPG8601 pressure indication unstable in DH Instruments ADCS-601?
If the FPG8601 pressure indication is unstable when the FPG8601 is bypassed (vented) in your DH Instruments Test Equipment, the piston-cylinder may need to be cleaned. Clean the piston cylinder.
What to do if PG7601 piston position readings seem incorrect in DH Instruments ADCS-601 Test Equipment?
If the PG7601 piston position readings seem incorrect in your DH Instruments Test Equipment, the piston position reading system may need to be adjusted. Execute the piston position detection adjustment procedure.
How to brighten a dim display on DH Instruments Test Equipment?
If the PPC3, RPM4 or PG7601 front panel display is dim on your DH Instruments Test Equipment, the screen saver option may have been activated. Press any key to resume full screen power, and adjust the screen saver activation time if desired.
Why PG7601 automated pressure control is not starting in DH Instruments Test Equipment?
If the PG7601 automated pressure control (GEN) is not starting after setting a target and loading mass, and the measurement mode is absolute by vacuum in your DH Instruments Test Equipment, it is because in absolute by vacuum measurement mode, before automated pressure generation begins, the reference vacuum must be below 20 Pa. Wait for the vacuum to reach less than 20 Pa, and check and correct the vacuum supply if it is inadequate.
Details technical specifications of the ADCS-601, covering power, pressure, and environmental requirements.
Specifies ambient conditions, measurements, and module details for the PG7601 piston gauge.
Outlines general specifications for the FPG8601, covering ambient conditions and pressure parameters.
Defines the pressure measurement and control capabilities and parameters of the ADCS-601 system.
Details the PG7601 and FPG8601 pressure standards, including their modules and associated handlers.
Step-by-step instructions for setting up the PG7601 and FPG8601 systems.
Procedures for initializing and verifying the operation of the PG7601, FPG8601, and the overall ADCS-601 system.
Procedures for safely shutting down and restarting the ADCS-601 system.
Covers zeroing, spanning, and validating the FPG8601 load cell and its linearity.
Provides a checklist of common symptoms, probable causes, and solutions for ADCS-601 issues.
General| Brand | DH Instruments |
|---|---|
| Model | ADCS-601 |
| Category | Test Equipment |
| Language | English |
To Next Page