TABLE OF CONTENTS
Page I © 2005 DH Instruments, Inc.
T
T
A
A
B
B
L
L
E
E
O
O
F
F
C
C
O
O
N
N
T
T
E
E
N
N
T
T
S
S
TABLE OF CONTENTS...............................................................I
TABLES ..................................................................................V
FIGURES................................................................................VI
ABOUT THIS MANUAL .............................................................IX
1. INTRODUCTION .................................................................1
1.1 SPECIFICATIONS....................................................................................................................................1
1.1.1 ADCS SYSTEM GENERAL SPECIFICATIONS............................................................................................1
1.1.2 PG7601 PISTON GAUGE SPECIFICATIONS...............................................................................................2
1.1.2.1 AMBIENT AND PISTON-CYLINDER CONDITION MEASUREMENTS ....................................................2
1.1.2.2 PISTON-CYLINDER MODULE ..................................................................................................................2
1.1.2.3 MASS SET.................................................................................................................................................3
1.1.3 FPG8601 GENERAL SPECIFICATIONS.......................................................................................................3
1.1.3.1 AMBIENT AND PISTON-CYLINDER CONDITION MEASUREMENTS ....................................................3
1.1.4 PRESSURE MEASUREMENT AND CONTROL SPECIFICATIONS ............................................................3
1.1.4.1 10 TO 380 KPA, PG7601 AND PPC3-700K ..............................................................................................3
1.1.4.2 1 TO 15 KPA, FPG8601 AND PPC3-100K ................................................................................................4
2. SYSTEM OVERVIEW ...........................................................5
2.1 ADCS-601 SYSTEM.................................................................................................................................5
2.1.1 REFERENCE BENCH..................................................................................................................................12
2.1.2 CONTROL CABINET...................................................................................................................................13
2.1.3 GAS SUPPLY PANEL .................................................................................................................................15
2.2 PRESSURE STANDARDS.....................................................................................................................16
2.2.1 PG7601 PISTON GAUGE............................................................................................................................16
2.2.1.1 PG7601 PLATFORM................................................................................................................................17
2.2.1.2 PG7601 TERMINAL.................................................................................................................................17
2.2.1.3 PG7601 10 KPA/KG PISTON-CYLINDER MODULE...............................................................................18
2.2.1.4 AMH-38 AUTOMATED MASS HANDLER ...............................................................................................19
2.2.1.5 AMH-38 MASS SET.................................................................................................................................21
2.2.2 FPG8601 FORCE BALANCED PISTON GAUGE .......................................................................................21
2.2.2.1 FPG8601 PLATFORM .............................................................................................................................23
2.2.3 PPC3 PRESSURE CONTROLLERS...........................................................................................................23
2.2.4 RPM4 A116K REFERENCE PRESSURE MONITOR..................................................................................25
2.3 VACUUM PUMPS ..................................................................................................................................27
3. INSTALLATION ................................................................ 29
3.1 UNPACKING AND INSPECTION...........................................................................................................29
3.1.1 ADCS CONTROL CABINET........................................................................................................................30
3.1.2 ADCS REFERENCE BENCH AND ACCESSORIES...................................................................................30
3.1.3 PG7601 PLATFORM AND BELL JAR ........................................................................................................32
3.1.4 PG7601 PISTON-CYLINDER MODULE (PC-7100/7600-10,TC) ................................................................32
3.1.5 PG7601 MASS SET (MS-AMH-38)..............................................................................................................33
3.1.6 PG7601 AUTOMATED MASS HANDLER (AMH-38) ..................................................................................34
3.1.7 FPG8601 PLATFORM, PISTON-CYLINDER AND ACCESSORIES...........................................................34
3.1.8 FPG8601 MASS SET (MS-8601-2)..............................................................................................................35
3.1.9 SCROLL VACUUM PUMPS ........................................................................................................................35
3.1.10 TURBO MOLECULAR VACUUM PUMP.....................................................................................................35
3.1.11 SYSTEM CONTROLLER.............................................................................................................................36
3.2 SITE REQUIREMENTS..........................................................................................................................36
To Next Page
Loading...