DIEBOLD NIXDORF D2156 - Power Button Lock and Unlock Functionality

To Next Page

To Previous Page

Display Settings

6.2

6.2 Power button - Lock/Unlock

The power button is unlocked by default. The user can switch the display on and off discretely, indepen-

dent of the connected system. If the power button is locked, the user cannot manually switch the display

on or off.

NOTE

If RMT is enabled, the power button will initiate RMT signal to the host system only

when there is single PLINK connection. If the display is powered by DC-Jack or USB-C,

then RMT signal will not be initiated.

Confidential External

01750368517 B

6-4

Main Page

Table of Contents3
Manufacturer's Declaration and Approval8
Supplier's Declaration of Conformity11
Introduction12
From Point-Of-Sale to Point-Of-Service12
Features at a Glance13
About this Manual14
Section-Specific Warning Notes14
Display Overview15
Touch Screen Per Model15
User Interface16
Front Panel16
Figure 5-1 D2156 - Front Panel16
Connector Panel18
Figure 5-2 D2156 - Connector Panel18
Display Settings19
Figure 6-1 Guiddcmonitorcontrol19
RMT Enable/Disable21
Power Button - Lock/Unlock22
Touch Technologies23
Projected Capacitive Touch Screen23
General Information23
Instructions for Using the Touch Screen23
Cleaning Instructions23
Initial Setup24
Unpacking and Checking the Delivery Unit24
Installing the Display to a Stand24
Figure 8-1 D2156 - Removing Screws25
Installing the Display to the Stand (Standard)26
Installing the Display to the Stand (with Cable Covers)28
Figure 8-2 D2156 - Removing Screws29
Connecting the Display33
Wall Mount33
Ergonomic Terminal Workplace34
Peripherals (Optional)35
Waiter Lock35
Installation35
Figure 10-1 Waiter Lock Kit35
Figure 10-2 Removing Waiter Lock Side Cover36
Figure 10-3 Sliding out the Side Cover36
Figure 10-4 Removing the Side-Attach Peripheral Connection Cover37
Figure 10-5 Side-Attach Peripheral Connection Cover Removed37
Figure 10-6 Fitting the Waiter Lock into the System38
Figure 10-7 Tightening the Waiter Lock Screws38
Figure 10-8 Waiter Lock Installed38
Figure 10-9 Front View with Waiter Lock39
Magnetic Swipe Card Reader (MSR)40
How to Operate40
Cleaning Instructions40
Installation40
Figure 10-10 MSR Kit40
Figure 10-11 Removing Side Cover of MSR Module41
Figure 10-12 Removing the Side-Attached Peripheral Connection Cover41
Figure 10-13 Fitting the MSR Module into the System41
Figure 10-14 Tightening the Screws of the MSR Module42
Figure 10-15 MSR Module Installed42
Figure 10-16 Front View with MSR Module42
NFC Module43
Installation43
Figure 10-17 NFC Module Kit43
Figure 10-18 Removing the NFC Module Side Cover43
Figure 10-19 Sliding out the Side Cover44
Figure 10-20 Removing the Side-Attach Peripheral Connection Cover44
Figure 10-21 Side-Attach Peripheral Connection Cover Removed45
Figure 10-22 Fitting the NFC Module into the45
Figure 10-23 Tightening the Screws of the NFC Module46
Figure 10-24 NFC Module Installed46
Figure 10-25 Front View with NFC Module46
Barcode Reader (BCR)47
Overview47
Figure 10-27 Front View with BCR47
Installation48
Figure 10-28 Back View with BCR48
Figure 10-29 BCR Module48
Figure 10-30 Removing the BCR Top Cover48
Figure 10-31 Sliding out the BCR Top Cover49
Figure 10-32 Removing the Peripheral Connection Cover49
Figure 10-33 Docking the BCR to the System49
Figure 10-34 Swivelling the BCR Scanner50
Figure 10-35 Tightening the Locking Screws50
Swivel Angle51
Fingerprint Reader (FPR) Module51
Cleaning Instruction52
Installation54
Technical Data59
Dimensions60
Projected Capacitive Touch Screen61
Supported Resolutions61
NFC Module61
Barcode Reader64
Ibutton66
Msr68
Fingerprint Reader Module70

DIEBOLD NIXDORF D2156 - Power Button Lock and Unlock Functionality

Table of Contents

Related product manuals