Why are the upper lights on my Dimplex DS5603 not bright?
If the upper lights in your Dimplex Stove are not bright or visible, it could be due to burnt-out light bulbs, which you should replace. Alternatively, there could be loose wiring; in that case, check the wiring connections. A defective light harness could also be the cause, and it would need to be replaced.
How to fix a Dimplex DS5603 that does not turn on manually?
If your Dimplex Stove isn't turning on manually, it could be due to several reasons. First, refer to the Operation Section. Check the fuse/breaker panel for incoming voltage from the electrical wall socket. Also, check wiring connections for any loose wiring. The On/Off or 3-Position Switch might be defective (replace it, depending on the model). Finally, the Remote Control Receiver could be defective (replace it and initialize with the Remote Control).
Why does my Dimplex DS5603 Stove heater turn off after a couple of minutes?
If the heater on your Dimplex Stove turns off after a few minutes, it could be due to a buildup of dirt or dust in the heater assembly. Ensure that the exterior intake louvers and firebox cavity are free of dirt and dust. Alternatively, the Heater Assembly might be defective and needs to be replaced.
What to do if Dimplex DS5603 does not turn on using the remote control?
If your Dimplex Stove isn't turning on with the remote control, first, refer to the Operation Section. The Remote Control may not be initialized to the fireplace, so initialize it. If the remote isn't working, install a new battery and reinitialize it if needed. If these steps don't work, the Remote Control or Remote Control Receiver may need to be replaced and initialized.
Why is my Dimplex DS5603 Stove heater fan on but there is no heat?
If the heater fan in your Dimplex Stove turns on but isn't producing heat, first, refer to the Operation Section. Check for loose wiring by tracing the wiring in the unit. The Heater On/Off Switch or the Thermostat might be defective, requiring replacement. In some cases, the Heater Assembly itself may be defective and need replacement.
Why does the circuit breaker trip when I turn on my Dimplex DS5603?
If the circuit breaker trips or a fuse blows when you turn on your Dimplex Stove, it could be due to a short in the unit's wiring. In this case, trace the wiring in the unit. Alternatively, the circuit may be overloaded. Additional appliances might be drawing too much power. Try plugging the unit into another outlet or installing it on a dedicated 15 amp circuit.
Why is the flame shuddering in my Dimplex DS5603?
If the flame in your Dimplex Stove is shuddering, it is likely due to a defective flicker motor, which needs to be replaced.
Why is light leaking around the log set of my Dimplex DS5603 Stove?
If light is leaking around the log set of your Dimplex Stove, the log set may not be positioned properly. Check the log set for proper fit.
Is it normal for the heating element in my Dimplex DS5603 to glow red?
Small glowing sections of the heating element in your Dimplex Stove are normal. However, if larger glowing sections are causing the heater to trip the thermal cutout, unplug the unit, discontinue use, and replace the heater assembly.
Why do the lights dim when my Dimplex Stove is on?
If the lights dim in the room when your Dimplex Stove is on, the unit may be drawing close to the circuit's current rating. Try moving the unit to another outlet or installing it on a dedicated 15 amp circuit.
General| Model Number | DS5603 |
|---|---|
| Type | Electric Stove |
| Heat Output | 1.5 kW |
| Fuel Type | Electric |
| Flame Effect | Optiflame |
| Color | Black |
| Thermostat | Yes |
| Remote Control | Yes |
| Timer | Yes |
| Safety Features | Overheat protection |
| Weight | 15 kg |
| Power Output | 1.5 kW |
To Next Page
