How to fix missing dots on Domino Printer?
If one or more dots are missing from the print (particularly at the bottom) when using a Domino Printer with a remote or inclined print head, the controller may be too low in relation to the print head. Raise the controller slightly, observing the print until the dot(s) reappear.
How to troubleshoot a Domino C1000 plus LCD that is not working?
If the LCD on your Domino Printer is not working, check the following: * Ensure the control unit power cable from the base unit is correctly plugged in. Turn off the mains power before checking the interconnections. * Check the mains fuse in the plug and replace it if it's blown. * Make sure the mains power cable is correctly attached to the base unit. Turn off the mains power first, then refit the cable, ensuring it's in the correct position. * Verify that the base unit power is switched on. The On/Off switch at the top of the base unit should be illuminated.
Why is ink leaking from my Domino C1000 plus?
If you notice ink leaking from the Domino Printer's control unit head or base unit body, the following could be the cause: * The ink line may be damaged or loose. Power down the unit, locate the damaged component, and clear up any ink spill. * There may be a damaged valve in the base unit. Power down the unit and clear up any ink spill. * The QR connector to the control unit may be damaged. Power down the unit and clear up any ink spill. * The ink may be overfilling the header tank and leaking back through the tank vent and control valve.
What to do if Domino Printer sensor misses items when counting?
If the sensor on your Domino Printer misses items when counting, consider the following: * The sensor lens may be dirty. Clean the lens with Domino cleaning agent. * The print surface may be too far away. Use an external sensor or guidance rails on the conveyor. * Print surfaces may be bunching up on the conveyor. Ensure there is a sufficient gap between surfaces.
How to adjust print height on a Domino Printer?
If the print is too high or low on the print surface when using your Domino Printer, it may be because the control unit is set too high or low in relation to the conveyor. To fix this, lower or raise the control unit assembly on the mounting bracket.
How to fix channels not printing on Domino C1000 plus?
If one or more channels are not printing on your Domino Printer, it may be due to dust or dirt on the nozzle plate. Prime the print head to clean the nozzle plate.
What to do if unable to exit menu on Domino Printer?
If you're unable to exit from a particular function or menu icon on your Domino Printer, you may be pressing the incorrect key.
Why is the LCD screen too dim on my Domino Printer?
If the LCD screen on your Domino Printer is too dim to read, it may be because the cover screen is scratched or dirty. Clean the control unit with Domino cleaning solution.
How do I correct upside down print on Domino C1000 plus?
If your Domino Printer is printing the message back to front or upside down, it's likely that the message direction and orientation are set incorrectly. Readjust these settings through the main menu bar.
How to adjust print position on Domino Printer?
If the print is too far to the right or left on the print surface when using your Domino Printer, the delay setting may be incorrect. To resolve this, change the delay setting in the parameters menu.
General guidelines for safe printer operation, installation, and maintenance.
Precautions regarding ink flammability and electrostatic discharge prevention.
Safe handling procedures for ink, including eye and skin contact precautions.
Instructions for mounting the base unit on a stand or conveyor.
Information on using a bracket to mount two print heads side-by-side.
Procedures for mounting and dismounting the control unit head.
Steps for adjusting the vertical position of the control unit.
Instructions for rotating the remote print head by 90 degrees for specific models.
Procedure for setting up the print head to print at an angle for C6000i.
Setup procedure for the C6000v print head for vertical printing.
Procedure for setting print angles for C3000X and C1000X models.
Procedure for releasing air flow vents before initial printer operation.
Step-by-step guide for replacing the ink bottle in a 200ml base unit.
Step-by-step guide for replacing the ink bottle in a 2 litre base unit.
Instructions on how to safely switch on the printer after connections are made.
Specific instructions for priming the C6000v print head.
Procedure for priming a rotated print head for specific models.
Steps to reset the control unit to factory default settings.
Steps for creating new text, barcode, or graphic messages.
Guide to typing text, managing lines, and selecting text sizes.
Process for naming and saving a completed message.
Adding sell-by date information to messages in various formats.
Incorporating time, date, and shift codes into messages.
Adding incremental, decremental, or pallet counts to messages.
Creating and configuring various types of bar codes for messages.
Daily cleaning tasks for the printer unit, including LCD and keypad.
Comprehensive inspection and filter replacement every six months.
Procedures for cleaning the print head nozzle plate for optimal print quality.
General| User Interface | Touchscreen |
|---|---|
| Supply Voltage | 100 - 240 VAC |
| Frequency | 50/60 Hz |
| Operating Temperature | 5°C to 40°C |
| Print Speed | Up to 75 m/min |
| Connectivity | Ethernet, USB |
To Next Page
