How to fix missing dots on Domino Printer?
If one or more dots are missing from the print (particularly at the bottom) when using a Domino Printer with a remote or inclined print head, the controller may be too low in relation to the print head. Raise the controller slightly, observing the print until the dot(s) reappear.
How to troubleshoot a Domino Printer LCD that is not working?
If the LCD on your Domino Printer is not working, check the following: * Ensure the control unit power cable from the base unit is correctly plugged in. Turn off the mains power before checking the interconnections. * Check the mains fuse in the plug and replace it if it's blown. * Make sure the mains power cable is correctly attached to the base unit. Turn off the mains power first, then refit the cable, ensuring it's in the correct position. * Verify that the base unit power is switched on. The On/Off switch at the top of the base unit should be illuminated.
Why is ink leaking from my Domino Printer?
If you notice ink leaking from the Domino Printer's control unit head or base unit body, the following could be the cause: * The ink line may be damaged or loose. Power down the unit, locate the damaged component, and clear up any ink spill. * There may be a damaged valve in the base unit. Power down the unit and clear up any ink spill. * The QR connector to the control unit may be damaged. Power down the unit and clear up any ink spill. * The ink may be overfilling the header tank and leaking back through the tank vent and control valve.
What to do if Domino C6000 plus Printer sensor misses items when counting?
If the sensor on your Domino Printer misses items when counting, consider the following: * The sensor lens may be dirty. Clean the lens with Domino cleaning agent. * The print surface may be too far away. Use an external sensor or guidance rails on the conveyor. * Print surfaces may be bunching up on the conveyor. Ensure there is a sufficient gap between surfaces.
How to adjust print height on a Domino C6000 plus?
If the print is too high or low on the print surface when using your Domino Printer, it may be because the control unit is set too high or low in relation to the conveyor. To fix this, lower or raise the control unit assembly on the mounting bracket.
How to fix channels not printing on Domino C6000 plus?
If one or more channels are not printing on your Domino Printer, it may be due to dust or dirt on the nozzle plate. Prime the print head to clean the nozzle plate.
What to do if unable to exit menu on Domino C6000 plus?
If you're unable to exit from a particular function or menu icon on your Domino Printer, you may be pressing the incorrect key.
Why is the LCD screen too dim on my Domino C6000 plus?
If the LCD screen on your Domino Printer is too dim to read, it may be because the cover screen is scratched or dirty. Clean the control unit with Domino cleaning solution.
How do I correct upside down print on Domino C6000 plus?
If your Domino Printer is printing the message back to front or upside down, it's likely that the message direction and orientation are set incorrectly. Readjust these settings through the main menu bar.
How to adjust print position on Domino C6000 plus?
If the print is too far to the right or left on the print surface when using your Domino Printer, the delay setting may be incorrect. To resolve this, change the delay setting in the parameters menu.
Recommendations for safe installation, usage, and maintenance of the printer.
Specifications for the printer's remote print head, including dimensions and conduit length.
Specifications for the printer's control unit, including dimensions and material.
Specifications for the printer's base unit, including finish, dimensions, and weight.
Procedures for replacing the ink bottle in the printer.
Specific steps for replacing the ink bottle in a 200ml base unit.
Specific steps for replacing the ink bottle in a 2 litre base unit.
Guidance on connecting the printer's base unit and control units.
Details on making connections for the printer base unit.
Details on making connections for the printer control units.
Step-by-step instructions to power on the printer unit.
Procedure for priming the printer's print head(s) for optimal quality.
Steps to set up a print job, including positioning the printer.
Inserting message attributes like sell-by-date, time, and counts.
Detailed steps for entering sell-by-date information into a message.
Using real-time commands for time, date, and shift code insertion.
Adding box and pallet counts to messages, incrementally or decrementally.
Steps for generating and configuring bar codes for messages.
Steps for generating and configuring data matrix codes for messages.
Steps for generating and configuring QR codes for messages.
Adjusting parameters like speed, resolution, and delay for message quality.
How to adjust the print speed parameter to match conveyor speed.
How to adjust the print resolution (dots per inch) for quality.
How to adjust the message delay for proper positioning on the print surface.
How to adjust the magnification (width) of bar codes.
Adjusting bar code raster thickness for improved readability.
Daily cleaning and maintenance steps for the printer unit.
How to clean the printer's nozzle plate using the prime function.
Specific head cleaning procedure for the C6000V model.
How to mount the print head for horizontal printing.
Resolving issues with print height, position, quality, and orientation.
Troubleshooting ink leaks, weeping, and ink out warnings.
General| Print Technology | Thermal Transfer |
|---|---|
| Print Resolution | 300 dpi |
| Print Width | 53 mm |
| Connectivity | Ethernet, USB |
| Ribbon Width | 55 mm |
| Supported Media Types | Labels |
| Media Thickness | 0.05 mm to 0.2 mm |
| Operating Temperature | 5°C to 40°C (41°F to 104°F) |
| Weight | 22 lbs (10 kg) |
To Next Page
