31
1838-065 Issued 3-19
Version D
Program the 4 different tone open functions (see chart below) for Relays 0, 1 and 2. Each number of a four-digit number code
controls each of the 4 functions. If the function is not desired, enter # instead of a number. If Expansion boards are connected
to the 1838, there is no need to set a momentary activation tone open number for the Expansion control relay(s). However, you
may want to program HOLD and RELEASE tone open numbers, that can allow ONLY management to have a way to automati-
cally unlock ALL doors/gates controlled by ALL the Expansion boards at once during an emergency (see section 5.2.2).
Factory setting:
Relay 0 = (# # # #) #-no momentary, #-no hold, #-no release, #-no hold 1 hour
Relay 1 = (9 8 7 6) 9-momentary, 8-hold, 7-release, 6-hold 1 hour
Relay 2 = (5 4 3 2) 5-momentary, 4-hold, 3-release, 2-hold 1 hour.
3.3.3 Tone Open Numbers
This programming sequence sets which relay(s) will activate when the switch input (main terminals #4 and #6) is activated on
the 1838. It can be programmed so that only one relay will activate, or any combination of relays will activate in step 2.
TIP: The relay that you designate as the primary relay should be programmed to activate from the postal switch input.
Factory setting = 010 (“0”relay 0-will NOT activate)(“1”relay 1-WILL activate)(“0”relay 2-will NOT activate)
3.3.4 Switch Input Relay(s) Activation
1. Press and enter your four-digit MASTER CODE (beep).
2. Press (beep) to set Relay 0, OR (beep) to set Relay 1, OR (beep) to set Relay 2 tone numbers.
3. Enter a four-digit tone open number code, then press (beep).
Example: If you want a relay to have a momentary activation function only when the number 9 is pressed, enter 9 # # #.
If a function is not desired, enter # instead of a number in that digit position. DO NOT duplicate any 4 digits.
Example: DO NOT program relay 0 tone open number code to 9999, 0 relay will NOT function.
4. Repeat steps 2 and 3 to set other relay tone open numbers.
5. Press together to end this programming sequence (beeeeeep).
? ? ? ?
5
0
0 1 2
0
1. Press and enter your four-digit MASTER CODE (beep).
2. Enter the three-digit (1's or 0's only) relays activation code, then press (beep).
Three-digit positions: 1st digit position - Relay 0, 2nd digit position - Relay 1, 3rd digit position - Relay 2.
To activate a relay - enter a 1 in a digit position.
To NOT activate a relay - enter a 0 in a digit position.
Example: entering 010 will cause only relay 1 to activate. Entering 101 will cause both relay 0 and relay 2 to activate.
3. Press together to end this programming sequence (beeeeeep).
? ? ? ?
0
5
0
1st Digit
2nd Digit
3rd Digit
4th Digit
Momentary activation. Relay will activate for the programmed strike time (3.3.1).
Hold. Relay will activate and remain activated until commanded to release.
Release. Deactivates the relay hold command.
Hold 1-hour. Relay will activate for 1-hour and then will automatically deactivate itself.
4-Digit Tone Open Number Code Relay Function After Digit has been Pressed on Phone
This programming is only used when a DKS Remote Call Station is connected to the 1838. It will set the 1838 to dial out in
either a touch-tone or rotary format. Generally, this will be set for touch-tone.
Factory setting = touch-tone.
3.3.5 Touch-Tone / Rotary-Dial
1. Press and enter your four-digit MASTER CODE (beep).
2. Press (beep) for touch-tone, OR (beep) for Rotary
3. Press together to end this programming sequence (beeeeeep).
? ? ? ?
7
0
0 1
0
1st Digit
2nd Digit
3rd Digit
4th Digit
To Next Page
Loading...
