9150-065-V-12-12
44
8.3 Accessory Items
The following accessory items are available for the model 9150 slide gate operator.
Contact Sensors - For use as a secondary entrapment protection device. Miller Edge, Inc., MGO20, MGR20, MGS20
Photo Cell - Non-contact (photocell) sensors for use as a secondary entrapment protection device.
MMTC, Inc. Model IR55 - P/N 8080-010 MMTC, Inc. Model 60-278 - P/N 8080-011
Carlo Gavazzi Type PMP12 - P/N 8080-030 Carlo Gavazzi Type PMT - P/N 8080-031
Loop Detector - Detectors plug directly into ports on circuit board simplifying wiring.
Single channel detector - P/N 9410-010 Dual channel detector - P/N 9409-010
Loop Wire - 18 AWG loop wire with XLPE insulation is ideal for ground loops. Available in 500 and 1000 foot rolls. Red, blue or
black insulation.
Pre-Fab Loops - Prefabricated ground loops. 24-foot circumference with 50-foot lead-in. Available in yellow, red or blue jackets.
Not for use in asphalt roadways.
Loop Test Meter - Meg-ohm meter checks the integrity of ground loops. P/N 9401-045
Remote Alarm/Reset Station - Provides a remote station to reset an operator in a hard shutdown condition. Must be mounted
in line-of-site of the gate and operator. Includes visual alarm light and audible siren. P/N 1404-080.
3-Button Control Station - Provides open-close-stop manual operation of the gate.
Stand Alone Box - P/N 1200-006 Interior (fits in single gang box) - P/N 1200-007
Interconnect Cable - Interconnect wire cable contains all the necessary wires to interconnect primary / secondary operators.
Cable length: 30 ft. - P/N 2600-755 40 ft. - P/N 2600-756 50 ft. - P/N 2600-757
Time Clock - 7 day and 365 day time clocks can be used to automatically open gate at pre-set time and days. Compact clock fits
inside the operator. 7 day clock - P/N 2600-791 365 day clock - P/N 2600-795
V-Wheels - 4 inch and 6 inch. UHMW or Steel. Roller bearings or sleeve bearings. Single or tandem wheel configurations.
Endless Idler Assembly with Protective Cover - Use when gate operator chain needs 180° return. P/N 2600-818
Guide Rollers with Protective Covers - A variety of sizes to support slide gates.
Gate End Retainer - Fits on top of end post and helps stabilize the end of the gate in the open or closed position (End post NOT
provided). P/N 1204-004
Base Plate for 9150 - Required for post mount installation. P/N 2600-495 (6 x 6 steel posts NOT provided).
Base Plate Stop Brackets for 9150 - Required for post mount installation when using chain stops. P/N 2600-970
Additional #40 Chain - 20 ft. per box. P/N 2600-442
9150 Fail-Secure Manual Release Kit - Changes the Fail-Safe manual release to a Fail-Secure manual release. P/N 2600-865
High Voltage Kit - Alter the input AC voltage on a 115 VAC 9150 to 208, 230, 460 or 575 VAC. P/N 2600-266
115 VAC Heater with Fan Assembly Kit - Thermostatically controlled heater and fan for cold and hot environments.
For 115 VAC input power ONLY. P/N 1601-154
208/230 VAC Heater with Fan Assembly Kit - Thermostatically controlled heater and fan for cold and hot environments.
For 208/230 VAC input power ONLY. P/N 1601-197
460 VAC Heater with Fan Assembly Kit - Thermostatically controlled heater and fan for cold and hot environments.
For 460 VAC input power ONLY. P/N 1601-198
Surge Devices - High and low voltage surge suppressors help prevent circuit board failure caused by lightning strikes and
power surges. High Voltage - P/N 1879-080 Low Voltage - P/N 1878-010
Gate Scale - Use to test torque required to move gate. P/N 2600-225
Speed Bumps - Prefabricated six-foot speed bump reduces traffic speed through gate system. P/N 1610-150
To Next Page
Loading...
