To Next PageTo Next Page
Why does cloud slicer show Dremel 3D45 printer offline?
If the cloud slicer will not connect to your Dremel 3D45 or shows "printer offline", check the 3D45 network settings and retry the connection, as the 3D45 may not be connected to the network.
How to fix filament not sticking to build platform on Dremel 3D45 3D Printers?
If the filament isn't extruding or sticking properly to the build platform of your Dremel 3D Printers, it could be due to the build platform not being level with the extruder head. Leveling the build platform will align the extruder head and ensure better object quality. Cancel your object, clear the build platform, level it, and then restart the object.
How to fix Dremel 3D45 that froze before print?
If the Dremel 3D45 froze before your object started, it might have received conflicting commands. To resolve this, turn the power switch off, wait 30 seconds, and then turn the power switch back on.
What to do if Dremel 3D Printers build did not start when sent over network?
If your Dremel 3D printer build didn't start when sent over the network, consider the following: * **Filament:** Ensure you have enough filament. Load additional filament and resume the build. * **Doors:** The doors must be closed to start builds over your network; start the build from the print queue. * **Build Plate:** The build plate must be clear to start a build over your network; clear the build plate and start the build from the print queue.
Why Dremel 3D Printers 3D45 will not retrieve a token?
If your Dremel 3D45 printer won't retrieve a token, it could be due to: * Incorrect network password. Re-enter your password or verify it with your network owner. * Your network has a firewall. Try entering network proxy information.
How to fix invalid token on Dremel 3D45 3D Printers?
Use "Get new token" to generate a new token and retry connection. Note this will remove any users that are sharing your printer.
Why won't my Dremel 3D45 connect to my network?
If your Dremel 3D45 won't connect to your network, try repositioning it closer to your wireless router. Also, double-check and re-enter your network password or SSID, or verify the password with your network owner, as an incorrect password or SSID could be the reason.
What to do if Dremel 3D45 3D Printers print ends in spaghetti mess?
If you see a spaghetti mess at the end of your Dremel 3D Printers build, it could be because a layer of your object didn't stick properly, the model was saved with minimal surface area contacting the build platform, or the object was built floating above the build platform without supports. Also, the Z-Gap offset may not be correct, causing improper spacing between the extruder tip and the build platform. Use the preview feature in your slicing software to check the first layer height and position. Build with supports when necessary. Contact customer service on how to calibrate the Z-Gap Offset.
What to do if Dremel 3D45 will not retrieve token?
If your Dremel 3D45 will not retrieve a token, re-enter your password or verify your password with your network owner, as the network password might be incorrect. If that doesn't work, your network may have a firewall, so enter network proxy information.
General| Layer Resolution | 50 - 300 microns |
|---|---|
| Filament Diameter | 1.75 mm |
| Nozzle Diameter | 0.4 mm |
| Max Extruder Temperature | 280 °C |
| Max Bed Temperature | 100 °C |
| Technology | Fused Filament Fabrication (FFF) |
| Heated Bed | Yes |
| Print Speed | Up to 150 mm/s |
| Enclosed Print Chamber | Yes |
| Connectivity | USB, Wi-Fi, Ethernet |
| Supported Filaments | PLA, Nylon, PETG, ECO-ABS |
| Printer Dimensions | 515 x 406 x 403 mm |
| Display | Full-color touchscreen |
| Power Requirements | 100 - 240 V, 50/60 Hz |
