EasyManuals Logo

Dremel 3D45 Original Instructions

Dremel 3D45
396 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
ORIGINAL INSTRUCTIONS
GENERAL SAFETY WARNINGS
!
WARNING
READ ALL
INSTRUCTIONS IN THIS
MANUAL AND FAMILIARIZE YOURSELF
WITH THE DREMEL 3D45 BEFORE SETUP
AND USE. FAILURE TO COMPLY WITH THE
WARNINGS AND INSTRUCTIONS MAY RESULT IN
FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE,
OR PERSONAL INJURY. SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE REFERENCE
WORK AREA SAFETY
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not operate Dremel 3D45 in the presence of
Dremel 3D45
creates high temperatures which may ignite the
dust or fumes.
c. 
Injury can occur in
hands of untrained users.
ELECTRICAL SAFETY
a. 

Improper grounding and modied plugs
increase risk of electric shock.
b. 
locations. Do not expose Dremel 3D45 to rain.
Presence of moisture increases risk of electric
shock.
c. 


Damaged or entangled cords
increase the risk of electric shock.
d. 
storm. There may be a remote risk of a power
surge from lightning that may result in an electric
shock.
e. 

PERSONAL SAFETY
a. 



or medication. A moment of inattention while
operating Dremel 3D45 may result in personal
injury.
b. The use of
protective equipment such as heat resistant gloves
and safety glasses will reduce the risk of personal
injuries.
c. 

Loose clothes, Jewellery
or long hair can be caught in moving parts.
DREMEL 3D45 USE AND CARE
a. 


that may affect the Dremel 3D45’s operation.


Use of Dremel 3D45 when
damaged may result in poor quality of object
creation, further equipment damage, property
damage or personal injury.
b. 

it has cooled down to at least 60°C (140°F).
Contact with the extruder tip or heated build
platform during or after operation before tip has
cooled may result in personal injury.
c. 




Dremel 3D45 melts plastic during building. Plastic
odours emitted during Dremel 3D45 operation
may irritate eyes and airways. Locating Dremel
3D45 close to surrounding objects prevents proper
ventilation.
d. Do not reach inside the Dremel 3D45 while it is
in operation. Contact with Dremel 3D45 moving
parts during operation may result in poor build
quality, equipment damage or personal injury.
e. 
operation. Use of Dremel 3D45 by persons
unfamiliar with these warnings and instructions may
result equipment or property damage and personal
injury.
f. Use of lament not
authorized by Dremel may result in equipment,
property damage or personal injury.
 

 Heating lament above
recommended range can cause emissions that may
result in personal injury.
h. 
Small
objects are potential choking hazards for young
children.
i. 

j. 

Plastic may melt when
exposed to re or other heat sources. Such use of
objects created by Dremel 3D45 may result in re,
property damage and personal injury.
k. 
intended for food or drink applications

Such use of objects created by
Dremel 3D45 may result in illness or personal
injury.
l. 

Dremel
lament is not suitable for electrical applications.
Such use of objects created by Dremel 3D45 may
result in property damage and personal injury.
m. 
Dremel lament is not suitable for food
or drink preparation and food utensils. Such use
of objects created by Dremel 3D45 may result in
illness or personal injury.
n. 
Dremel lament
is not suitable for chemical storage. Such use of
GB
2

Table of Contents

Other manuals for Dremel 3D45

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Dremel 3D45 and is the answer not in the manual?

Dremel 3D45 Specifications

General IconGeneral
Layer Resolution50 - 300 microns
Filament Diameter1.75 mm
Nozzle Diameter0.4 mm
Max Extruder Temperature280 °C
Max Bed Temperature100 °C
TechnologyFused Filament Fabrication (FFF)
Heated BedYes
Print SpeedUp to 150 mm/s
Enclosed Print ChamberYes
ConnectivityUSB, Wi-Fi, Ethernet
Supported FilamentsPLA, Nylon, PETG, ECO-ABS
Printer Dimensions515 x 406 x 403 mm
DisplayFull-color touchscreen
Power Requirements100 - 240 V, 50/60 Hz

Related product manuals