Program Descriptions: 5.4 Assigning Keypad Zones
17
reporting code for the programmed Transmission Delay
Period. (See 5.15
“Transmission Delay”
on page 23.)
• Wireless Zone – This attribute determines which zones
are to have wireless devices. This allows the panel to gen-
erate a low battery trouble and zone supervisories for the
wireless zones.
NOTE: Any zone with the wireless attribute enabled will not
cause an alarm for a fault condition when armed (or any time
for 24-hour zones).
Zone Attributes. . . . . . . . . . . . Sections [101] - [108]: [1] - [8]
5.4 Assigning Keypad Zones
“Z” keypads have zone inputs to which devices—such as
door contacts—can be connected. (See 2.12
“Keypad Zones”
on page 6 for wiring information.)
Once the keypad zones are installed, assign the zone in pro-
gramming section [020] Keypad Zone Assignments.
Enter the 2 digit zone designated for each keypad (slot) from
01-08.
Keypad Zone Assignments . . . . . . . . . . . . . . . . . . . . . . [020]
5.5 Communicator – Dialing
If the Communicator Disable option is selected, the panel
will not attempt to call central station. If communication is
enabled, the panel will attempt to call central station when an
event with a valid reporting code occurs. (See 5.8
“Communi-
cator – Reporting Codes”
on page 18.)
The Communicator Call Direction options are used to select
which telephone number the panel will dial when an event
occurs.
If the DTMF Dialing option is enabled, the panel will dial using
DTMF (touch tone). If the Switch to Pulse Dial option is
enabled, the panel will switch to pulse dialing on the fifth
attempt to call the central station. When this option is dis-
abled, the panel will always dial using DTMF. If DTMF Dialing
is disabled, the panel will always pulse dial.
When the Force Dialing option is enabled, the panel will dial
out regardless of the presence of dial tone. Each dialing
attempt will follow this pattern:
a) the panel picks up the telephone line and searches for dial
tone for 5 seconds
b) if no dial tone is found, the panel hangs up and waits for 20
seconds
c) the panel picks up the telephone line again and searches
for a dial tone for 5 seconds
d) the panel will then dial regardless of the presence of dial
tone
If there is no initial handshake recognized within 40 seconds
the panel will then hang up the line.
If the Force Dialing option is disabled, each attempt will still
follow the above pattern, except that the panel will not dial in
step d if no dial tone is detected.
The Delay Between Dialing Attempts timer adds a delay
before the next call is dialed.
If the Busy Tone Detection option is enabled, the panel will
hang up after detecting busy tone for 5 seconds and will
redial after the amount of time programmed in the Delay
Between Dialing Attempts section.
Maximum Dialing Attempts determines the maximum num-
ber of attempts the panel will make to send a signal to the
central station before indicating a Failure to Communicate
(FTC) trouble condition. The 3rd Telephone Number can be
used to back up the 1st in this situation. (See 5.7
“Communi-
cator – Telephone Numbers”
on page 17.) If a later communi-
cation attempt is successful, the FTC reporting code(s)
programmed in section [351] will be transmitted along with the
unreported events from an earlier unsuccessful communica-
tion.
When Bell on FTC when Armed is enabled in programming
section [702], option [8], an FTC during the armed period will
sound an Audible Alarm for the length of Bell time-out or until
the system is disarmed. If FTC Trouble Only when Armed is
enabled, only the keypad buzzer will sound trouble beeps
every 10 seconds until a key is pressed.
Post Dial Wait for Handshake determines the amount of time
the panel will wait for a valid handshake from the receiver. If
the panel does not hear the handshake it will consider the call
a failed attempt, hang up and try again.
The Pulse Dialing Make/Break Ratio option can change the
Make/Break ratio to 33/67 from the North American ratio of 40/
60.
With ID Tone Enabled the panel will pulse a tone on the tele-
phone line to indicate that the panel is on the line.
The 2100Hz/1300Hz ID Tone option selects the frequency of
the ID tone that is pulsed on the line.
NOTE:Contact your local telephone company to confirm which
settings should be used.
DTMF or Pulse Dialing . . . . . . . . . . . . . . . . .Section [380]: [3]
Switch to Pulse Dialing on Fifth Attempt . . .Section [380]: [4]
Communicator Enable/Disable . . . . . . . . . .Section [380]: [1]
Communicator Call Direction Options . . . Section [361]-[368]
Force Dialing . . . . . . . . . . . . . . . . . . . . . . . .Section [702]: [2]
Delay Between Dialing Attempts . . . . . . . . . . . .Section [703]
Busy Tone Detection . . . . . . . . . . . . . . . . . .Section [701]: [6]
Maximum Dialing Attempts . . . . . . . . . . . . . . . . Section [160]
Post Dial Wait for Handshake . . . . . . . . . . . . . .Section [161]
Pulse Dialing Make/Break Ratio. . . . . . . . . .Section [702]: [1]
ID Tone Enabled . . . . . . . . . . . . . . . . . . . . .Section [702]: [5]
2100Hz/1300Hz ID Tone . . . . . . . . . . . . . . .Section [702]: [6]
Bell on FTC/Trouble Only . . . . . . . . . . . . . . .Section [702]: [8]
5.6 Communicator – Account Numbers
The account number is used by the central station to distin-
guish between panels. There are two account numbers pro-
grammable for the PC1565.
First Account Code (4 digits). . . . . . . . . . . . . . .Section [310]
Second Account Code (4 digits) . . . . . . . . . . .Section [311]
5.7 Communicator – Telephone Numbers
The panel can use three different telephone numbers for com-
municating with the central station. The First Telephone
Number is the primary number, the Second Telephone Num-
ber is the secondary number and the Third Telephone Num-
ber will back up the First telephone number if enabled.
NOTE:The Third Telephone Number will NOT back up the Sec-
ond Telephone Number.
NOTE: If you enter a telephone number section (sections [301]
- [303]) at an LED keypad, pressing [#] will delete the pro-
grammed telephone number and change all the digits to [F].
If the Alternate Dial option is enabled, the panel will alternate
between the first and third telephone numbers when attempt-
ing to call the central station. If the option is disabled, the
To Next Page
Loading...
Need help?
General
