TYPICAL WIRING DIAGRAM
A larger diagram is available in the operators manual.
Deep Sea Electronics Plc.
Tel:+44 (0)1723 890099
Fax: +44 (0)1723 893303
LO CALL (from UK BT landlines) :
Telephone 0845 260 8933
Email:
Deep Sea Electronics inc.
Phone: +1 (815) 316-
Fax: +1 (815) 316-
TOLL FREE (USA only) : Tel: 1 866 636 9703
Email: dsesales@deepseausa.com
THE FRONT PANEL CONFIGURATION EDITOR.
•
Ensure the engine is at rest and the module is in S
TOP mode by pressing the Stop/Reset
• Press the Stop/Reset and Info
• If a module security PIN has been set, the PIN numb
shown :
• Press
(up) or
(down) to adjust
• Press (right)
when the first digit is correctly entered. The digit you have just entered will now
show ‘#’ for security.
•
Repeat this process for the other digits of the PIN
to move back to adjust one of the previous digits.
•
When
is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is
not correct, you must re-enter the PIN.
•
If the PIN has be
en successfully entered (or the module PIN has not been
enabled), the editor is displayed .
EDITING A PARAMETER
• Enter the editor as described above.
•
Press the or
to cycle to the section you wish to view/change.
to cycle to the parameter
within the section you have chosen.
• To edit the parameter, press
to enter edit mode. The parameter begins to flash to indicate that
you are editing the value.
• Press the up
or down
buttons to
change the parameter to the required value.
• Press to save the value. The parameter
ceases flashing to indicate that it has been saved.
• To exit the editor at any time, press and hold the
D E E P S E A E L E C T R O N I C S
8 6 6 0
I N S T A L L A T I O N I N S T R U C T I O N S
Deep Sea Electronics inc.
TOLL FREE (USA only) : Tel: 1 866 636 9703
Email: dsesales@deepseausa.com
NOTE: When the
NOTE: When the NOTE: When the
NOTE: When the
editor is visible, it is automatically exited after 5 minutes of inactivity to
editor is visible, it is automatically exited after 5 minutes of inactivity to editor is visible, it is automatically exited after 5 minutes of inactivity to
editor is visible, it is automatically exited after 5 minutes of inactivity to
ensure security.
ensure security.ensure security.
ensure security.
NOTE:
NOTE: NOTE:
NOTE:
The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or
automatically) to ensure security.
automatically) to ensure security.automatically) to ensure security.
automatically) to ensure security.
NOTE:
NOTE: NOTE:
NOTE:
More comprehensive module configuration is possible using the
More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the
More comprehensive module configuration is possible using the
configuration software
configuration softwareconfiguration software
configuration software.
. .
.
Please contact us for further details
Please contact us for further detailsPlease contact us for further details
Please contact us for further details
NOTE: The contents of the tables overleaf may differ depending on the actual module
NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module
NOTE: The contents of the tables overleaf may differ depending on the actual module
configuration.
configuration. configuration.
configuration.
THE FRONT PANEL CONFIGURATION EDITOR.
Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset
button.
If a module security PIN has been set, the PIN number request
is then
when the first digit is correctly entered. The digi
t you have just entered will now
(left) if you need
is pressed after editing the final PIN digit, the P
IN is checked for validity. If the number is
en successfully entered (or the module PIN has not
been
to cycle to the section you wish to view/change.
Then press
or
within the section you have chosen.
to enter edit mode. The parameter begins to flash t
o indicate that
change the parameter to the required value.
ceases flashing to indicate that it has been saved.
or button.
D E E P S E A E L E C T R O N I C S
I N S T A L L A T I O N I N S T R U C T I O N S
053-070
ISSUE 1
editor is visible, it is automatically exited after 5 minutes of inactivity to
editor is visible, it is automatically exited after 5 minutes of inactivity to editor is visible, it is automatically exited after 5 minutes of inactivity to
editor is visible, it is automatically exited after 5 minutes of inactivity to
The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or
More comprehensive module configuration is possible using the
More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the
More comprehensive module configuration is possible using the
86
8686
86xx series PC
xx series PC xx series PC
xx series PC
Please contact us for further details
Please contact us for further detailsPlease contact us for further details
Please contact us for further details
NOTE: The contents of the tables overleaf may differ depending on the actual module
NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module
NOTE: The contents of the tables overleaf may differ depending on the actual module
http://bestgenerator.spb.ru/?page_id=6765
To Next Page
Need help?
General
