13
PROGRAMMING & OPERATION INSTRUCTIONS
“X” CONTROLLER
Timer Resolution
The Timer displays time in two (2) different scales. From 0
to 60 minutes, the timer is displayed in Minutes/Seconds
(“MN” Mode). From 1 to 12 hours, the time is displayed in
Hours/Minutes (“HR” Mode). The mode indicators are
located in the first number digit to the left of the colon.
Temperature Scale
The controller can be set to display the temperature in °F or
°C as follows:
• Turn Power Switch to COOK position.
• Set TIME to 00:00 and TEMP so “20” is displayed
in the right two temperature digits.
• Press and hold both the START TIME and
CANCEL buttons for 5 seconds. The control will
display “CCC” and “FFF” in the temperature digits to
indicate it has entered the mode.
• Turn the TIME or TEMP dial to toggle between
“CCC” and “FFF”.
• Press CANCEL to exit.
Power Input Frequency
The controller can be set to operate on 50Hz or 60Hz as
follows:
• Turn Power Switch to COOK position.
• Set TIME to 00:00 and TEMP so “40” is displayed
in the right two temperature digits.
• Press and hold both the START TIME and
CANCEL buttons for 5 seconds. The control will
display “50” and “60” to indicate it has entered the
mode.
• Turn the TIME or TEMP dial to toggle between
“50” and “60”.
• Press CANCEL to exit.
Actual Temperature Button
The actual temperature can be viewed by pressing and
holding the START TIME button for approximately 2
seconds. The temperature will be displayed in the
temperature digits. This can be viewed anytime the oven is
in operation, except when the oven is in the HOLD mode.
Pulse
The controller can be set to operate the fan continuously, or
cycle on and off every 30 seconds during the COOK cycle
as follows:
• Turn Power Switch to COOK position.
• Set TIME to 00:00 and TEMP to 000.
• Press and hold both the START TIME and
CANCEL buttons for 5 seconds. The control will
display “COn” or “CYC” to indicate it has entered the
mode.
• Turn the TIME and TEMP dial to toggle between
“COn:” and “CYC”.
• Press CANCEL to exit.
The fan can not be set to cycle if the HOLD mode is to be
used.
Fan Speed Switch
The fan speed can be set to high or low speed by placing
FAN HI/LOW switch to the desired setting. The display
does not indicate which mode the fan is operating.
Cool Down
This feature enables the oven to be cooled rapidly by
allowing the fan to operate with the heating elements turned
off. To activate, turn the Power Switch to the COOL
position and open the oven door. When the door is opened
enough to disengage the door switch, the fan will turn on.
Closing the door will turn the fan off.
Cooking
A cooking cycle can be initiated as follows:
• Turn Power Switch to COOK position.
• Set the cooking time by turning the TIME dial until
the desired time is shown on the display.
• Set the desired cooking temperature by turning the
TEMP dial until the desired temperature is shown on
the display. The indicator light will turn on and the
display will flash when a minimum temperature of
150°F is entered. The flashing display indicates that
the oven is in its Preheating Mode. It will no longer
flash once the oven reaches the temperature set point.
The indicator light will cycle on and off with the
heating elements.
• Press the START TIME button to begin the timed
cooking cycle. Pressing the CANCEL button will
“zero” the timer at any time.
Cook & Hold
The controller can be set to hold the oven at a set
temperature at the end of the cooking cycle as follows:
• Turn Power Switch to COOK position.
• Set TIME to 00:00 and TEMP so “50” is displayed
in the right two temperature digits.
• Press and hold both the START TIME and
CANCEL buttons for 5 seconds. The control will
display “HOLD” in the time digits, and the current
Hold Set Temperature in the temperature digits to
indicate it has entered the mode.
• Turn the TIME or TEMP dial to set the desired
temperature. Setting it to “000” will turn the Hold
mode off.
• Press CANCEL to exit.
When the timer counts down to zero, the alarm will sound
for 5 seconds and “HOLD” will appear in the display with
the current hold temperature. The timer will not count up.
Manual timing is required.
To Next Page
Loading...
