Configuration Control
The Configuration control provides access to additional impor-
tant control functions. Pushing the
Configuration button once
shows the currently selected function. You can cycle through the
functions by pushing this button repeatedly.
The table below shows selections that can be controlled.
The Configuration LED, the FPD (front panel display) and the OSD
(on-screen display) will turn on when the button is pressed. The
LED, FPD, and OSD will turn off automatically after 30 seconds.
13
Displays and Controls
(continued)
Configuration FPD shows Description
Test Patterns TEST This menu allows you to select the 27 different test patterns available in the iScan HD+. Push the ▲ or ▼ button to
select one of the test patterns. Push the Test Patterns button on the remote control to activate the selected test pat-
tern. Push the button again to deactivate the test pattern. Refer to the Test Patterns section of this guide for more
details on using the Test Patterns feature of the iScan HD+
Auto Standby STBY The default setting is OFF, which means iScan HD+ will always be in Active mode regardless of the activity state of the
selected input. If Auto Standby is ON, iScan HD+ will go into Standby mode 30 seconds after the selected input becomes
inactive. To see the current setting, first press ▲ or ▼. Then press the same button again to change the setting.
HDCP Mode HDCP There are 3 HDCP modes:
OFF: HDCP is disabled at the iScan HD+'s DVI input. Some sources will turn off HDCP in this case and the iScan
HD+ will drive a non-HDCP DVI display or an analog display.
ON: The iScan HD+ will continuously look for a HDCP display device on its DVI output.
AUTO: The iScan HD+ will look for a HDCP display device for a limited time, after which it will output blue screen
to a non-HDCP display.
Power LED PLED Allows you to configure the behavior of the Power LED.
OFF: Turns the Power LED off at all times
ON: Turns the Powe LED on. LED turns blue when the system is processing the an input signal. LED turns red in
standby mode. LED turns green in pass-through mode.
AUTO: LED turns off after approximately 30 seconds without user interaction.
User Mode USRM You have limited access to the output timing controls in ‘Normal’ mode. In ‘Advanced’ user mode, you have access
to the complete set of output timing controls. See the section entitled “Customizing the Output Video Timing for your
Display”. Push the ▼ button to see the current setting. The FPD will display either ‘NORM’ for normal or ‘ADV’ for
advanced user level. Pushing the ▼ button again selects the alternate mode.
Serial Port Rate R232 The serial port is used by the automation system controllers to control the iScan HD+. Refer to the Automation Control
section of this guide for more information. The serial port baud rate defaults to 19200 bps but can be changed using
the ▲ or ▼ button. The supported baud rates are:
1.2K 1200 bps 4.8K 4800 bps 14.4K 14400 bps 38.4K 38400 bps
2.4K 2400 bps 9.6K 9600 bps 19.2K 19200 bps 57.6K 57600 bps
Factory
Default
FCTD Allows you to reset system settings to the factory default. First press either the ▲ or ▼ button. The FPD will show ‘NO’.
Then press the same button to switch to ‘YES’. Confirm this selection by pressing the Enter/Exit button.
The default factory settings are:
Input Selection : Auto
Input Aspect Ratio : 16:9
Picture Controls : midrange (0)
Sharpness (Component) : Off
Chroma Filter (CUEC) : Off
Output Aspect Ratio : 16:9
Output Resolution : 480P
Sync : Sync on Y
Output Color Space : YPbPr
Output Type : Analog
Auto Standby : Off
Frame Rate : 60Hz input - 1:1 source-locked output
50Hz input - unlocked at 59.94 Hz
User Mode : Normal
Video Input Priority Settings :
Digital Audio Input Assignment :
Software
Update
SWUP You can upgrade your iScan HD+ firmware using this command. First press the ▲ or ▼ button. The FPD will show ‘NO’.
Then press the same button to switch to ‘YES’. Confirm this selection by pressing the
Enter/Exit button. Care must
be taken before performing a firmware upgrade. Make sure you really want to do this. Once the ‘YES’ selection is
confirmed, the FPD will show ‘LOAD’. If you change your mind, you can wait for about 5 minutes for the command
to be cancelled or you can power cycle the system by unplugging the DC Power input jack.
The About Box INFO This shows information about the system including Input Status, Output Status and System Version number.
Press the ▲ or ▼ button to activate.
Configuration
Control Menu
1– Component 1
2– Component 2
3– S-Video 1
4– S-Video 2
5– Video 1
6– Video 2
7– DVI
8– SDI
9– Analog Passthru
Component 1 - Audio 1
Component 2 - Audio 4
S-Video 1 - Audio 2
S-Video 2 - Audio 3
Video 1 - Off
Video 2 - Off
DVI - Off
SDI - Off
Analog Passthru - Off
To Next Page
Loading...