EasyManua.ls Logo

Dyna-Glo BFSS10LPT-2P - User Manual

Dyna-Glo BFSS10LPT-2P
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
VENT-FREE
BLUE FLAME
GAS WALL HEATER
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
WARNING: This appliance is equipped for
(natural or propane) gas. Field conversion is not
permitted.
- Do not store or use gasoline or other ammable vapors and Iiquids in vicinity of this or
any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the re department.
- Installation and service must be performed by a qualied installer, service agency or the
gas supplier.
This is an unvented gas-red heater. It uses air (oxygen) from the room in which it is
installed. Provisions for adequate combustion and ventilation air must be provided.
Refer to Air For Combustion and Ventilation section on page 8 of this manual.
This appliance may be installed in an aftermarket, permanently located, manufactured (mobile)
home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases.
C US
C US
ANS Z21.11.2-2013
Gas Fired Room Heaters
Volume II - Unvented Room Heaters
IMBFSS - 2018-03-21
MODEL #
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-447-4768, 8:30 a.m. – 4:30 p.m., CST, Monday – Friday or
email us at customerservice@ghpgroupinc.com.
Propane
BFSS10LPT-2P
BFSS20LPT-2P
BFSS30LPT-2P
Natural Gas
BFSS10NGT-2N
BFSS20NGT-2N
BFSS30NGT-2N

Table of Contents

Questions and Answers

  • T
    Tony ThomasSep 4, 2025
    What causes burner backfiring during combustion in a Dyna-Glo BFSS10LPT-2P?
    • M
      Michael NelsonSep 4, 2025
      If the burner is backfiring during combustion in your Dyna-Glo Gas Heater, clean the burner orifice. If the problem continues, contact your dealer or customer service, or consider replacing the gas regulator.
  • M
    Madison BooneSep 18, 2025
    Why does my Dyna-Glo Gas Heater make a clicking/ticking noise after the burner is lit or shut off?
    • H
      Hector VazquezSep 18, 2025
      This clicking/ticking noise is common with most Dyna-Glo Gas Heaters. If the noise is excessive, contact a qualified service technician.
  • H
    Heather LongSep 16, 2025
    Why is there slight smoke or odor during the initial operation of my Dyna-Glo Gas Heater?
    • C
      chad66Sep 16, 2025
      If you notice slight smoke or odor during the initial operation of your Dyna-Glo Gas Heater, this problem will stop after a few hours of operation.
  • K
    Katherine LittleSep 14, 2025
    Why is there white powder residue forming near my Dyna-Glo BFSS10LPT-2P Gas Heater?
    • C
      Crystal HobbsSep 14, 2025
      If you notice white powder residue forming within the burner box or on adjacent walls or furniture near your Dyna-Glo Gas Heater, turn the heater off when using furniture polish, wax, carpet cleaner, or similar products, as the vapors from these products turn into white powder residue when heated.
  • D
    danielrodriguezSep 12, 2025
    What to do if the fan is not spinning on my Dyna-Glo BFSS10LPT-2P? (Select Models)
    • C
      Cynthia SmithSep 13, 2025
      If the fan is not spinning on your Dyna-Glo Gas Heater, verify that the fan is plugged in and set to "MAN" or "AUTO". Allow 5-10 minutes for the fan to engage. If it still does not work, replace the fan.
  • P
    Pamela GoodwinSep 12, 2025
    Why does my Dyna-Glo Gas Heater produce a whistling noise when the burner is lit?
    • W
      Wendy CameronSep 12, 2025
      If your Dyna-Glo Gas Heater produces a whistling noise when the burner is lit, turn the control knob to the low (1) position and let it warm up for a minute. Operate the burner until air is removed from the line and have the gas line checked by your local propane/LP gas company. Observe minimum installation clearances, and clean the burner.
  • L
    Lisa HollandSep 9, 2025
    Why is the fan making a loud noise in my Dyna-Glo BFSS10LPT-2P Gas Heater? (Select Models)
    • C
      Christina CraigSep 9, 2025
      If the fan in your Dyna-Glo Gas Heater is making a loud noise, see "Cleaning Fan". Also, verify that the wiring is not in the fan path. If the problem persists, replace the fan.
  • A
    alyssawoodsSep 7, 2025
    Why does my Dyna-Glo Gas Heater produce unwanted odors?
    • A
      awallaceSep 7, 2025
      If your Dyna-Glo Gas Heater produces unwanted odors, ventilate the room and stop using odor-causing products while the heater is running, as the heater may be burning vapors from paint, hair spray, glues, etc. Locate and correct any gas leaks. For Propane /LP models, refill the supply tank.
  • H
    Hannah BowmanSep 5, 2025
    How to fix no spark at ODS/pilot when pressing the ignitor on a Dyna-Glo Gas Heater?
    • B
      Billy TorresSep 5, 2025
      If there is no spark at the ODS/pilot when the ignitor is pressed on your Dyna-Glo Gas Heater, replace the ODS. Also, replace the ignitor cable or free it if it is pinched by any metal or tubing, and keep the ignitor cable dry. You might also need to replace the ignitor or ignition module, or replace the battery.
  • J
    Jeffrey PhillipsAug 20, 2025
    What to do if my Dyna-Glo Gas Heater unit shuts off after a few minutes?
    • F
      fmartinAug 20, 2025
      If your Dyna-Glo Gas Heater shuts off after running for a few minutes, make sure the gas supply is turned on and the equipment shutoff valve is open. Fully press in the control knob while pressing the ignitor and continue holding it down, repeating the igniting operation until air is removed. You may also need to clean the ODS/pilot or replace the ODS/pilot assembly. Ensure the control knob is in the PILOT position. If problems persist, contact your local propane/LP gas company.

Dyna-Glo BFSS10LPT-2P Specifications

General IconGeneral
ModelBFSS10LPT-2P
BTU Output10, 000 BTU
Fuel TypeLiquid Propane
Ignition TypePiezo Ignition
Heating Area300 sq. ft.
Oxygen Depletion Sensor (ODS)Yes
Safety Shut-offYes
Safety FeaturesODS, Safety Shut-off
TypeBlue Flame
Mounting LocationWall or Floor

Related product manuals