What to do after Auto Channel Search on Dynex DX-42E250A12 if there are no channels?
If there are no channels after an Auto Channel Search on your Dynex LCD TV: * Reception can vary by channel depending on the broadcast power level of a given station. * Make sure the antenna or cable/satellite TV is connected securely to your TV. * Try replacing the cable between the antenna/cable or cable/satellite box and your TV.
What to do if my Dynex DX-42E250A12 has no power?
If your Dynex LCD TV has no power: * Ensure the power cord is correctly connected to your TV and a power outlet. * Unplug the power cord, wait 60 seconds, then plug it back in and turn on your TV. * Other devices may be interfering with your TV.
Why is there no picture and no sound on my Dynex DX-42E250A12 LCD TV?
If your Dynex LCD TV has no picture and no sound, try the following: * Press on the TV or the remote control. * Ensure the power cord is plugged in securely. * Verify that the video cables are connected securely to the back of your TV. * Select the correct video input source. * Try another channel. * Confirm the incoming signal is compatible. * Check that the antenna or cable TV is connected correctly and securely. * Adjust the contrast and brightness. * Check the closed caption settings.
What to do if my Dynex DX-42E250A12 LCD TV displays a 'No signal' error message?
If your Dynex LCD TV shows a 'No signal' error message: * Press the INPUT button and select the correct input for the device or service you are using. * If using a cable or satellite box, use its remote to change channels. * Ensure the correct input is selected to view channels from the cable or satellite box.
Why is there good picture but no sound on my Dynex LCD TV?
If you have a good picture but no sound on your Dynex LCD TV, consider the following: * Increase the volume and make sure that the sound is not muted. * Unplug the headphones. * Ensure that the correct audio mode is selected. * Verify that the audio cables are connected correctly and securely to the back of your TV. * Make sure that the antenna or cable TV is connected correctly and securely. * If you are using an antenna, the digital channel signal may be low. * The audio cable(s) you are using may be bad. Try a new set.
Why is my Dynex DX-42E250A12 LCD TV picture dark, poor, or not showing, but the sound is good?
If your Dynex LCD TV has a dark, poor, or no picture (screen is lit) but the sound is good, try these steps: * Try another channel. * Make sure that the antenna or cable TV is connected correctly and securely. * Adjust the brightness. * Make sure that the correct picture mode is selected. * If you are using an antenna, the digital channel signal may be low. * If you are using an antenna and the signal strength is low, adjust the antenna or use a highly directional outdoor antenna or set-top antenna with a built-in amplifier. * Make sure that the video cables are connected securely to the back of your TV. * The video cable(s) you are using may be bad. Try a new set.
What to do if some settings cannot be accessed on Dynex DX-42E250A12?
If a setting is grayed out on your Dynex LCD TV, it is not available in the current video input mode.
What to do if one or more channels do not display on Dynex DX-42E250A12 LCD TV?
If one or more channels do not display on your Dynex LCD TV: * Make sure that the channels are not blocked. * Make sure that the channels are not hidden. * If you are using a cable or satellite box, use the remote that came with that box to change channels. * Make sure you have the correct input selected to view channels from the cable or satellite box. * If you are using an antenna, the digital channel signal may be low.
What to do if my Dynex DX-42E250A12 LCD TV picture does not fill the screen?
If the picture on your Dynex LCD TV does not fill the screen and there are black bars around it, change the aspect ratio.
Why does my Dynex LCD TV only show snow (noise) on the screen?
If your Dynex LCD TV only shows snow (noise) on the screen, try these solutions: * Try another channel. * Make sure that the antenna or cable TV is connected correctly and securely. * If you are using an antenna, the digital channel signal may be low. * If you are using an antenna and the signal strength is low, adjust the antenna or use a highly directional outdoor antenna or set-top antenna with a built-in amplifier.
General| Screen Size | 42 inches |
|---|---|
| Display Type | LCD |
| Resolution | 1920 x 1080 |
| Aspect Ratio | 16:9 |
| Refresh Rate | 60Hz |
| HDMI Ports | 3 |
| USB Ports | 1 |
| Sound Output | 10W x 2 |
| Inputs | HDMI, Component, Composite, RF |
Safety tips for proper placement and use of the TV and furniture to prevent injury.
Precautions and guidelines for securely mounting the TV to a wall.
Alerts regarding electric shock, lightning, LCD panel handling, and replacement parts.
Step-by-step instructions for attaching the TV stand to the base plate.
Instructions for attaching a wall-mount bracket to the TV and wall.
Explanation of the function of each button on the remote control for TV operation.
Guide to choosing the optimal connection type for video quality based on device.
Instructions for connecting the TV's AC power cord to a power outlet.
Steps to connect a cable/satellite box using an HDMI cable for superior quality.
Steps to connect an antenna or cable TV directly to the TV's ANT/CABLE IN jack.
Steps to connect a DVD or Blu-ray player using an HDMI cable for best quality.
Steps to connect a VCR using AV cables.
Steps to connect a camcorder or game console using AV cables.
Steps for initial TV setup, including language, picture, and signal source.
Guide to adjusting picture settings like mode, brightness, contrast, and color.
Steps to adjust sound modes, balance, surround sound, and equalizer.
Instructions for setting or modifying the parental control password.
Guide to setting TV and movie rating controls for U.S. and Canada content.
Guide to programming universal remote controls for operation with the Dynex TV.
Solutions for common issues like no picture, no sound, or incorrect aspect ratios.
To Next Page