34
User Manual MN04200002E
Effective January 2016
C441 Ethernet module user manual
(C441R, C441T, C441U, C441V)
EATON www.eaton.com
Table 62. S611 Control Supervisor Instance Attributes (Cont.)
Attrib NV Access
Data
Type Name Description
153 NV Set/Get UINT Auxiliary Relay
Configuration
Auxiliary Relay Configuration
Behavior:
0 = Faulted
1 = Not Faulted
2 = Bypass
3 = Not In Bypass
4 = Motor Energized
5 = Motor Not Energized
154 NV Set/Get UINT User Interface
Display Config
User Interface Display
Configuration.
Value = Description
0 = Thermal Capacity
1 = Power Factor
2 = Line Frequency
3 = Current Unbal %
4 = Voltage Unbalance %
5 = Average pole temp
6 = Pole A Temp
7 = Pole B Temp
8 = Pole C Temp
155 NV Set/Get UINT UI Edit Lock Provides the ability to prevent
the user interface from making
configuration changes.
0 = Unlocked
1 = Locked
156 V Set/Get UINT Command
Register
1 = Clear Motor Run Hours
2 = Clear Motor Start Count
3 = Clear fault queue
255 = Force Overload Rest
(TP = 0)
250 = Force Comm Fault (unpub-
lished)
157 NV Set/Get UINT Communication
Loss Timeout
Communication Loss Timeout
Value (milliseconds)
158 NV Set/Get UINT EtherNet/IP
Comm Timeout
Range: 0–60,000 ms
Default: 3000 ms
Class 44 (0x2C): Overload Object
Instance Count: 1
Instance List: 1
Table 63. S611 Overload Object Instance Attributes
Attrib NV Access
Data
Type Name Description
4 NV Set/Get USINT Overload Class Overload Trip Class Setting.
6 V Get USINT Current
Unbalance
Percent Current Phase Imbalance.
(%)
7 V Get USINT Overload
Thermal
Memory
Thermal Capacity
0% Cold Motor
100% Will Cause an Overload
Trip (%)
101 V Get UINT Total Run Time Run Time in Hours. Total run time
can be reset through the command
parameter. (Hours)
102 V Get UINT Number of
Starts
Total number of starts can be reset
through the command parameter.
105 NV Set/Get UINT Scaled Overload
FLA
Scaled Overload FLA. Scaling fac-
tor is x10. (Amps)
106 V Get UINT Apparent Power
Factor
Apparent Power Factor * 100
107 V Get UINT Total Kilowatts Scaled Total Kilowatts. Scale fac-
tor is x10 (kW)
119 NV Set/Get UINT Current
Unbalance Trip
Delay
Trip Delay Applied to the
Unbalance Trip. (Seconds)
120 V Get UINT Current
Unbalance
Percent Current Phase Imbalance.
(%)
121 NV Set/Get UINT Jam Trip Delay Jam Trip Delay in Seconds. (sec-
onds)
122 NV Set/Get UINT Jam Trip Level Jam Trip Level Set in Percent of
FLA. (%)
123 NV Set/Get UINT Phase Loss Trip
Delay
Trip Delay Applied to the Phase
Loss Trip Sense. (seconds)
130 NV Set/Get UINT Reset Mode Method of Reset.
0 = Manual
1 = Auto
140 V Get UINT Average Current Average of the 3 Scaled RMS
Currents. (Amps)
141 V Get UINT Phase A RMS
Current
Scaled RMS Current of Phase A.
(Amps)
142 V Get UINT Phase B RMS
Current
Scaled RMS Current of Phase B.
(Amps)
143 V Get UINT Phase C RMS
Current
Scaled RMS Current of Phase C.
(Amps)
144 V Get UINT Residual
Ground Fault
Current
Scaled Residual Ground Fault
Current. Scaling = x100
152 V Get UINT Current Scale
Factor
Scale Factor for Current. Use this
value to scale the current values.
170 NV Set/Get UINT Load Disconnect
Trip Level
Load Disconnect Trip Level as a
Percent of Rated FLA. (%)
171 NV Set/Get UINT Load Disconnect
Trip Delay
Load Disconnect Trip Delay in
Seconds. (seconds)
172 NV Set/Get UINT Load Disconnect
Source
Load Disconnect Source:
0 = Under Power
1 = Under Current
173 NV Set/Get UINT Phase Loss Trip
Level
Trip Level for a Phase Imbalance
Trip. (%)
174 NV Set/Get UINT Stall Trip Level Stall Trip Level in Percent of FLA.
(%)
175 V Get INT Power Sign Indicates whether power is posi-
tive or negative. In the case of a
generator.
176 NV Set/Get UINT Residual GF
Start Delay
Length of time before the device
will begin to acknowledge the
ground fault current. (seconds)
To Next Page
Loading...
